NOIL2SM1300A View Datasheet(PDF) - ON Semiconductor

Part Name

Description

View to exact match

NOIL2SM1300A

LUPA1300-2: High Speed CMOS Image Sensor

ON Semiconductor 

NOIL2SM1300A

SPECIFICATIONS

Key Specifications

Table 1. GENERAL SPECIFICATIONS

Parameter

Specifications

Active Pixels

1280 (H) x 1024 (V)

Pixel Size

14 mm x 14 mm

Pixel Type

6T pixel architecture

Pixel Rate

630 Mbps per channel (12 serial

LVDS outputs)

Shutter Type

Pipelined and Triggered Global

Shutter

Frame Rate

500 fps at 1.3 Mpixel (boosted by

subsampling and windowing)

Master Clock

315 MHz for 500 fps

Windowing (ROI)

Randomly programmable ROI read

out up to four multiple windows

Read Out

Windowed, flipped, mirrored, and

subsampled readout possible

ADC Resolution

10−bit, on−chip

Extended Dynamic

Range

Multiple slope

(up to 90 dB optical dynamic range)

Table 2. ELECTRO−OPTICAL SPECIFICATIONS

Parameter

Conversion gain

Full well charge

Responsivity

Value

0.0325 LSB10/e-

30 ke-

63 LSB10/nJ/cm2 at 550 nm

Fill factor

40%

Parasitic light sensitivity < 1/10,000

Dark noise

1.2025 LSB10

QE x FF

35% at 550 nm

FPN

2% RMS of the output swing

PRNU

Dark signal

< 1% RMS of the output signal

162 LSB10/s, 5000 e-/s

Power dissipation

1350 mW

Absolute Maximum Ratings

Table 3. ABSOLUTE MAXIMUM RATINGS (Note 1)

Symbol

Description

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ABS (2.5 V supply group)

ABS rating for 2.5 V supply group

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ABS (3.3 V supply group)

ABS rating for 3.3 V supply group

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ABS (3.5 V supply group)

ABS rating for 3.5 V supply group

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ESD (Note 3)

HBM

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ CDM

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ LU

Latchup

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ TS (Notes 4 and 5)

ABS Storage temperature range

ABS Storage humidity range at 85°C

Min

−0.5

−0.5

−0.5

2000

500

200

−40

Max

3.0

4.3

4.3

+150

85

Units

V

V

V

V

V

mA

°C

%RH

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ RECOMMENDED OPERATING RATINGS

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ TJ (Notes 2 and 5)

Operating temperature range

−50

+85

°C

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. Absolute maximum ratings are limits beyond which damage may occur.

2. Operating ratings are conditions at which operation of the device is intended to be functional.

3. ON Semiconductor recommends that our customers become familiar with, and follow the procedures in JEDEC Standard JESD625−A.

Refer to Application Note AN52561. Long term exposure toward the maximum storage temperature will accelerate color filter degradation.

4. Caution needs to be taken to avoid dried stains on the underside of the glass due to condensation. The glass lid glue is permeable and can

absorb moisture if the sensor is placed in a high % RH environment.

5. HTS − High Temperature Storage was successfully completed on LUPA 1300-2 color devices at +150°C for 500 hours. Temperature Cycling

was successfully completed from −40°C to +125°C up to 1000 cycles. No reliability stress has been performed at −50°C.

www.onsemi.com

3

Share Link: