NT35510 View Datasheet(PDF) - Novatek Microelectronics
Part Name
Description
View to exact match
NT35510 Datasheet PDF : 211 Pages
| |||
PRELIMINARY
NT35510
4.6 Interface Logic Pins
Symbol
I/O
Description
RESX
This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
The input voltage range for RESX pin is related to DSTB_SEL and VSEL pins.
Input Voltage Level (DSTB_SEL=”0”)
Min.
Max. Unit
VDDI=1.65~3.3V
Logic High level input voltage
Logic Low level input voltage
0.7xVDDI
VSSI
VDDI
0.3xVDDI
V
V
I
VDDI=1.1~1.3V
Logic High level input voltage
Logic Low level input voltage
0.88
VSSI
1.35
V
0.55
V
TE
(TE_L)
TE_R
IM[3:0]
RGBBP
Input Voltage Level (DSTB_SEL=”1”)
VDDI=1.65~3.3V
Min.
Max.
VDDIL=1.1~1.3V
Min.
Max.
Unit
VSEL Logic High level input voltage 0.7xVDDI VDDI
1.155
1.95
V
=High Logic Low level input voltage VSSI 0.3xVDDI VSSI
0.585
V
VSEL Logic High level input voltage 0.88
1.35V
0.88
1.35V V
=Low Logic Low level input voltage VSSI
0.55
VSSI
0.55
V
Tearing effect output pin to synchronize MCU to frame writing, activated by S/W command.
O When this pin is not activated, this pin is output low.
If not used, please open this pin.
Tearing effect output pin to synchronize MCU to frame writing, activated by S/W command.
O The same output signal as TE (TE_L) pin.
If not used, please open this pin.
Interface type selection. The connections of IM[3:0] which not shown in table are invalid.
IM[3:0]
Display Data
Command
0000 80-series 8-bit MPU I/F, D[7:0] 80-series 8-bit MPU I/F, D[7:0]
0001 80-series 16-bit MPU I/F, D[15:0] 80-series 16-bit MPU I/F, D[15:0]
0010 80-series 24-bit MPU I/F, D[23:0] 80-series 24-bit MPU I/F, D[23:0]
0011 RGB I/F, D[23:0]
16-bit SPI (SCL rising edge trigger), SDI/SDO
1011 RGB I/F, D[23:0]
16-bit SPI (SCL falling edge trigger), SDI/SDO
I
0100
0101
RGB I/F, D[23:0]
MIPI DSI,
HSSI_D0_P/N, HSSI_D1_P/N
I2C I/F, I2C_SDA
MIPI DSI,
HSSI_D0_P/N, HSSI_D1_P/N
0110
MDDI,
HSSI_D0_P/N, HSSI_D1_P/N
MDDI, HSSI_D0_P/N, HSSI_D1_P/N
16-bit SPI (SCL rising edge trigger), SDI/SDO
1110
MDDI,
HSSI_D0_P/N, HSSI_D1_P/N
MDDI, HSSI_D0_P/N, HSSI_D1_P/N
16-bit SPI (SCL falling edge trigger), SDI/SDO
0111
MDDI,
HSSI_D0_P/N, HSSI_D1_P/N
MDDI, HSSI_D0_P/N, HSSI_D1_P/N
I2C I/F, I2C_SDA serial data
Display data written path control in RGB interface.
RGBBP=”0”, display data written to frame memory.
I RGBBP=”1”, display data written to line buffer (frame memory by pass mode)
When not used in other interfaces, please connect to VSSI.
11/8/2010
16
Version 0.00
With respect to the information represented in this document, Novatek makes no warranty, expressed or implied, including the warranties of merchantability,
fitness for a particular purpose, non-infringement, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any such
information.
Share Link: 