NT352 View Datasheet(PDF) - Unspecified

Part Name

Description

View to exact match

NT352

NORA TRACK & CONNECTORS

Unspecified 

Installation Instructions continued

NORA TRACK & CONNECTORS

NT-307 / NT-2307

Floating Feed

Mounting to outlet box at

any point on track. Locate

junction box in ceiling or on

wall containing two wires,

a black wire (Hot +) and a

white wire (Neutral -).

Make sure to splice white

to white and black to black.

Note: connect the green

ground wire to the green

ground screw or the green

ground wire in the junction

box.

GREEN

(if avail.)

WIRE

NUTS

****URGENT: READ PRIOR TO ATTEMPTING INSTALLATION***

EXISTING

JUNCTION BOX

NT-319

Monopoint

Insert the desired 120V AC lampholder into canopy observing

line polarity line. Maximum wattage: 300W

MOUNTING PLATE

MOUNTING

SCREWS (2)

BLACK

WHITE

FLOATING FEED

FLATHEAD,

PAINTED SCREWS

GREEN

(if avail.)

WIRE

NUTS

CEILING BOX

BLACK

WHITE

ADJUSTABLE

MOUNTING PLATE

MOUNTING

SCREWS (2)

CANOPY

POLARITY LINE

NT-305, NT-306, NT-329

NT-336, NT-2305, NT-2306,

NT-2329, NT-2336

Pendant Kit

1. Assemble Mounting strap to

existing junction box.

2. Assemble nuts on end of stem.

Slide canopy on and secure to

mounting strap using screw

threads and finished domed nuts

3. Assemble nuts to the other

end of stem leaving enough

space between nuts to allow

mounting bracket. Tighten nuts

securely.

4. May also be used with

T-bar clip (NT-332) for

unpowered structured support.

5. When connecting power

through stem, use NT-316 and

Wire Way Cover (NT-326)

JUNCTION BOX

COVER

NUT

TRACK

GROUND WIRE

STEM

CANOPY

SCREWHEAD

DECORATIVE NUT

MOUNTING

BRACKET

WIRE WAY COVER

12 AWG WIRES

TRACK

LIVE END FEED

CONNECTOR

SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

Read all instructions.

All electrical power is to be disconnected before adding to or changing the track configuration.

The one circuit track system has a maximum capacity of 20 amps or 2400 total watts when

permanently wired to an outlet box. Do not attempt to energize anything other than lighting track

fixtures on the track. To reduce the risk of fire and electric shock, do not attempt to connect

power tools, extension cords, appliances and the like to the track.

• Track light assembly must be installed a minimum of 6 inches from any combustible

surface or material, such as wall coverings or curtains.

• Track is not to be installed in wet or damp locations.

• Track system must be installed a minimum of 5 feet above the floor.

• Track not intended to be connected with power cord to more than one branch circuit unless

it is constructed so that it can be fed with more than one circuit. Check with a qualified

electrician. Although the track system may appear to operate acceptably, a dangerous

overload of the neutral may occur and result in a risk of fire.

FLATHEAD,

PAINTED SCREWS

NT-2311, NT-2316, NT-2321, NT-2348, NT-2352

NT-311, NT-316, NT-321, NT-348, NT-352

Live End Feed

Insert end of connector into track. Arrow on connector end is on

the same side as polarity groove on the track.

HOT WIRE

(BLACK)

NOTE: 2 hot wires for

2 citcuit track

GROUND WIRE

(GREEN)

NEUTRAL WIRE

(WHITE)

CONNECTOR POLARITY ARROW

POLARITY GROOVE

SCREW

TRACK

NT-328

Conduit Feed

Accept conduit for surface wiring. Track connector is

polarized. Ground contact is on same side as ground polarity

groove on track. Run conduit around or through beam or

around I-beam.

6505 Gayhart St., Commerce, CA 90040

2

Share Link: