NT352 View Datasheet(PDF) - Unspecified

Part Name

Description

View to exact match

NT352

NORA TRACK & CONNECTORS

Unspecified 

Installation Instructions

NORA TRACK & CONNECTORS

****URGENT: READ PRIOR TO ATTEMPTING INSTALLATION***

WARNING: FIRE/ELECTRICAL HAZARD

This equipment is intended to be installed only by qualified

personnel. The installation must be made in accordance

with the current edition to the National Electric Code and

all applicable state and local building codes.The final

installation must be approved by the appropriate qualified

electrical/building inspector(s). Improper installation may

result in a fire or electrical hazard. Be sure the electrical

power to the circuit has been disconnected before installing

this electrical system.

POWER FEED AND CONNECTORS

NT-309 / NT-2309

Flexible Connector

Joins two track sections at any angle

up to 90 degrees. Can be used for

wall to ceiling installation. Tighten

screw after installation into track.

FLEX JOINER

POLARITY ARROW

SCREW

POLARITY GROOVE

TRACK

NOTE: Track is UL listed strictly for 120V, 60Hz, 20Amp

power supply. Not for use with remote transformer(s).

DIMMING

Incandescent accepts standard rotary or slide dimmer.

Select dimmer with ample capacity for total number of

track fixtures. Low Voltage fixtures require use of solid

state (electronic) dimmer control capable of dimming

transformers. Example: Lutron. Compact Fluorescent and

HID fixtures cannot be dimmed.

INSTALLING NORA TRACK SECTION

Turn off power before beginning installation.

A. Secure mounting strap to outlet box. for adjustable, T-

and X-connector, a cover plate is required. If removal of

a knockout is required, remove it at this time.

B. NOTE: Make sure end cap at opposite end of track is

secured and butted against a surface. Slide feed

connector into end of track by aligning polarity arrow

on connector with polarity groove in track, secure with

the set screws provided. Using toggle bolts or screws

provided, attach track to ceiling. Secure feed connector

to outlet box, if applicable.

NT-310 / NT-2310

Mini Connector

Loosen set screw and

remove dead cap fitting.

Push connector

into open end of track.

LIVE END

LOOSEN SET SCREW AND

REMOVE DEAD END FITTING

NT-312 / NT-2312

Straight Connector

Connects two track

sections for a

straight run.

NT-313 / NT-2313

L-Connector

Connects two track sections at

a 90 degree angle.

GROUND CONDUCTOR SIDE WITH

POLARITY GROOVE

DEAD END

GROUND CONDUCTOR

TIGHTEN END SCREWS AFTER

INSTALLATION INTO TRACK

POLARITY GROOVE

TRACK

STRAIGHT CONNECTOR

L-CONNECTOR

POLARITY GROOVE

TRACK

ADDING NEW CONNECTOR

If adding additional sections to existing track remove end

cap from existing track. Slide new connector into open

end of existing track and tap with rubber mallet to secure

proper fit.

ADDING NEW TRACK

Secure end cap into non-connecting end of new track.

Slide new track into connector and tap with rubber mallet

for proper fit with no gap. Secure to ceiling according to

instructions above.

WIRING NORA TRACK SECTION

1. Run wire through outlet box mounting strap (if present)

and connector.

2. Connect positive wire (black) to the screw terminal

marked P.

3. Connect the neutral wire (white) to the screw terminal

marked N.

4. Connect the ground wire to green-finished screw

terminal.

5. See track fixture instructions for installation of fixture

onto track.

6. Track rated at 120V, 60Hz, 20 Amps.

WIRING CONNECTORS

Connectors are factory wired for correct polarity. Wiring

patterns can be changed easily in the field

by merely shifting jumper positions or eliminating wires.

When replacing or rewiring, be sure to maintain correct

polarity.

6505 Gayhart St., Commerce, CA 90040

NT-314 / NT-2314

T-Connector

Joins three track sections. Track

connector is polarized.

NT-315 / NT-2315

X-Connector

Joins up to four track sections.

Track connector is polarized.

SCREWS (4)

REMOVABLE

COVER PLATE

GREEN

GROUND

SCREW

SCREWS (3)

REMOVABLE

COVER PLATE

NICKEL CONTACT

SCREW (TYP)

POLARITY GROOVE

IN TRACK (TYP)

TRACK (TYP)

GROUND

CONDUCTOR (TYP)

POWER BODY

POWER BODY

SILVER GROUND

CONTACT (TYP)

BRASS CONTACT

SCREW (TYP)

PLASTIC PLUG

LOCK SCREW (TYP)

GREEN GROUND SCREW

POLARITY GROOVE

IN TRACK (TYP)

TRACK (TYP)

GROUND

CONDUCTOR (TYP)

POWER BODY

NICKEL CONTACT

SCREW (TYP)

POWER BODY

SILVER GROUND

CONTACT (TYP)

POWER BODY

PLASTIC PLUG

BRASS CONTACT LOCK SCREW (TYP)

SCREW (TYP)

(TYP) = TYPICAL

1

Share Link: