CY7C135-15(2004) View Datasheet(PDF) - Cypress Semiconductor
Part Name
Description
View to exact match
CY7C135-15
(Rev.:2004)
(Rev.:2004)
Cypress Semiconductor
CY7C135-15 Datasheet PDF : 12 Pages
| |||
CY7C135
CY7C1342
Maximum Ratings[1]
Storage Temperature ..................................–65°C to+150°C
Ambient Temperature with
Power Applied..............................................–55°C to+125°C
Supply Voltage to Ground Potential
(Pin 48 to Pin 24) ............................................ –0.5V to+7.0V
DC Voltage Applied to Outputs
in High Z State ................................................ –0.5V to+7.0V
DC Input Voltage[2]......................................... –3.0V to +7.0V
Electrical Characteristics Over the Operating Range[4]
Static Discharge Voltage........................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-Up Current.................................................... > 200 mA
Operating Range
Range
Commercial
Industrial
Ambient
Temperature
0°C to +70°C
–40°C to +85°C
VCC
5V ± 10%
5V ± 10%
7C135–15 7C135–20
7C1342–1 7C1342–2 7C135–25
5
0
7C1342–25
Parameter
Description
Test Conditions
Max Min Max
Max Uni
Min. .
.
. Min. .
t
VOH
Output HIGH Voltage
VCC = Min., IOH = –4.0 mA
2.4
2.4
2.4
V
VOL
Output LOW Voltage
VCC = Min., IOL = 4.0 mA
0.4
0.4
0.4 V
VIH
Input HIGH Voltage
2.2
2.2
2.2
V
VIL
Input LOW Voltage
0.8
0.8
0.8 V
IIX
Input Load Current
GND ≤ VI ≤ VCC
–10 +10 –10 +10 –10 +10 µA
IOZ
Output Leakage Current Outputs Disabled,
GND ≤ VO ≤ VCC
–10 +10 –10 +10 –10 +10 µA
ICC
Operating Current
VCC = Max.,
IOUT = 0 mA
Com’l
Ind.
220
190
180 mA
190
ISB1
Standby Current
(Both Ports TTL Levels)
Cf =ELfMaAnXd[5C] ER ≥ VIH,
Com’l
Ind.
60
50
40 mA
50
ISB2
Standby Current
(One Port TTL Level)
Cf =ELfMaAnXd[5C] ER ≥ VIH,
Com’l
Ind.
130
120
110 mA
120
ISB3
Standby Current
Both Ports CE and CER ≥ Com’l
15
15
(Both Ports CMOS Levels) VCC – 0.2V,
VorINV≥INV≤C0C.2–V0, .f2=V0[5]
Ind.
15 mA
30
ISB4
Standby Current
One Port CEL or
Com’l
125
115
100 mA
(One Port CMOS Level)
CER ≥ VCC – 0.2V,
VIN ≥VCC – 0.2V or VIN ≤ 0.2V,
Ind.
115
Active Port Outputs, f =
fMAX[5]
Notes:
1. The Voltage on any input or I/O pin cannot exceed the power pin during power-up.
2. Pulse width < 20 ns.
3. TA is the “instant on” case temperature.
4. See the last page of this specification for Group A subgroup testing information.
5. fMAX = 1/tRC = All inputs cycling at f = 1/tRC (except output enable). f = 0 means no address or control lines change. This applies only to inputs at CMOS level standby ISB3.
Document #: 38-06038 Rev. *B
Page 3 of 12
Share Link: