Introduction
This datasheet contains the description of the device features, pinout, electrical characteristics, mechanical data and ordering information.
• For complete information on the STM8S microcontroller memory, registers and peripherals, please refer to the STM8S microcontroller family reference manual (RM0016).
• For information on programming, erasing and protection of the internal Flash memory please refer to the STM8S Flash programming manual (PM0051).
• For information on the debug and SWIM (single wire interface module) refer to the STM8 SWIM communication protocol and debug module user manual (UM0470).
• For information on the STM8 core, please refer to the STM8 CPU programming manual (PM0044).

Description
The STM8S005xx value line 8-bit microcontrollers offer 32 Kbytes of Flash program memory, plus 128 bytes of data EEPROM. They are referred to as medium-density devices in the STM8S microcontroller family reference manual (RM0016). All devices of the STM8S005xx value line provide the following benefits: performance, robustness, reduced system cost, and short develoment cycles.
Device performance and robustness are ensured by true data EEPROM supporting up to 100 000 write/erase cycles, advanced core and peripherals made in a state-of-the art technology, a 16 MHz clock frequency, robust I/Os, independent watchdogs with separate clock source, and a clock security system.
The system cost is reduced thanks to high system integration level with internal clock oscillators, watchdog and brown-out reset.
Common family product architecture with compatible pinout, memory map and modular peripherals allow application scalability and reduced development cycles.
All products operate from a 2.95 to 5.5 V supply voltage.
Full documentation is offered as well as a wide choice of development tools.

FEATUREs
Core
   • 16 MHz advanced STM8 core with Harvard architecture and 3-stage pipeline
   • Extended instruction set
Memories
   • Medium-density Flash/EEPROM:
      - Program memory: 32 Kbytes of Flash memory; data retention 20 years at 55°C after 100 cycles
      - Data memory: 128 bytes of true data EEPROM; endurance up to 100 k write/erase cycles
   • RAM: 2 Kbytes
Clock, reset and supply management
   • 2.95 V to 5.5 V operating voltage
   • Flexible clock control, 4 master clock sources:
      - Low power crystal resonator oscillator
      - External clock input
      - Internal, user-trimmable 16 MHz RC
      - Internal low power 128 kHz RC
   • Clock security system with clock monitor
   • Power management:
      - Low power modes (wait, active-halt, halt)
      - Switch-off peripheral clocks individually
   • Permanently active, low consumption power-on and power-down reset
Interrupt management
   • Nested interrupt controller with 32 interrupts
   • Up to 37 external interrupts on 6 vectors
Timers
   • 2x 16-bit general purpose timers, with 2+3 CAPCOM channels (IC, OC or PWM)
   • Advanced control timer: 16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization
   • 8-bit basic timer with 8-bit prescaler
   • Auto wake-up timer
   • Window and independent watchdog timers
Communications interfaces
   • UART with clock output for synchronous operation, Smartcard, IrDA, LIN
   • SPI interface up to 8 Mbit/s
   • I2C interface up to 400 Kbit/s
Analog-to-digital converter (ADC)
   • 10-bit, ±1 LSB ADC with up to 10 multiplexed channels, scan mode and analog watchdog
I/Os
   • Up to 38 I/Os on a 48-pin package including 16 high sink outputs
   • Highly robust I/O design, immune against current injection
Development support
   • Embedded single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging