MC100EL39DWR2G(2016) 查看數據表（PDF） - ON Semiconductor
零件编号
产品描述 (功能)
生产厂家
MC100EL39DWR2G Datasheet PDF : 7 Pages
| |||
MC100EL39
Table 5. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0.0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE Power Supply Current
50
59
50
59
54
61 mA
VOH Output HIGH Voltage (Note 2)
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
VOL Output LOW Voltage (Note 2)
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
VIH Input HIGH Voltage (Single-Ended)
−1165
−880 −1165
−880 −1165
−880 mV
VIL Input LOW Voltage (Single-Ended)
−1810
−1475 −1810
−1475 −1810
−1475 mV
VBB Output Voltage Reference
−1.38
−1.26 −1.38
−1.26 −1.38
−1.26 V
VIHCMR Common Mode Range (Differential)
(Note 3)
VPP < 500 Mv
−3.7
VPP ≥ 500 mV
−3.5
−0.4 −3.8
−0.4 −3.6
−0.4 −3.8
−0.4 −3.6
V
−0.4
−0.4
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1.0 V.
Table 6. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fMAX
tPLH
tPHL
Maximum Toggle Frequency
Propagation Delay to Output
CLK → Q (Differential)
CLK → Q (Single-Ended)
MR → Q
1.0
1.0
1.0
GHz
ps
850
1150 900
1200 950
1250
850
1150 900
1200 950
1250
600
900 610
910 630
930
tSKEW Within-Device Skew (Note 2)
Q0−Q3
50
50
50
ps
Part-to-Part
Q0−Q3 (Diff)
200
200
200
tJITTER Random CLOCK Jitter (RMS) @ 1.0 GHz
2.0 3.0
2.0 3.0
2.0 3.0 ps
tS
Setup Time
EN → CLK
DIVSEL → CLK
ps
250
250
250
400
400
400
tH
Hold Time
CLK → EN
CLK → Div_Sel
ps
100
100
100
150
150
150
VPP
Input Swing (Note 3)
tRR
Reset Recovery Time
tPW
Minimum Pulse Width
150
CLK 500
MR 700
1000 150
100
500
700
1000 150
100
500
700
1000 mV
100 ps
ps
tr, tf
Output Rise/Fall Times Q (20%−80%)
280
550 280
550 280
550 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
1. VEE can vary +0.8 V / −0.5 V. Outputs are terminated through 50 W resistor to VCC − 2.0 V.
2. Skew is measured between outputs under identical transitions.
3. VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈40.
www.onsemi.com
4
Share Link: 