L9686D 查看數據表（PDF） - STMicroelectronics

零件编号

产品描述 (功能)

生产厂家

L9686D

AUTOMOTIVE DIRECTION INDICATOR

STMicroelectronics 

L9686

ELECTRICAL CHARACTERISTICS (– 20°C < Tamb <, 100°C, 8V < VS < 18V unless otherwise speci-

fied.)

Symbol

Parameter

Test Condition

Min. Typ. Max. Unit

VS

Operating Voltage

8

18

V

V2 – V1 Clamping Voltage

see note 1

27

34

V

V2 – V3

R2

Output Saturation Voltage

Starter Resistance

IRL = 250mA

see note 2

1.7

V

3.6

KΩ

KN

Oscillator Constant KN (normal Fn = 1/KnRoCo

Operation)

Osc. Frequency

1.27

1.74

CT

Temperature Coefficient of Kn See Note 3

–1.5 ⋅

1/°C

10-3

D.C.

Duty Cycle (normal operation)

45

50

55

%

KC

Oscillator Constant KC

(lamp failure detection)

FC = 1KcRoCo

Osc. Frequency

0.53

0.74

DCLF

Duty Cicle (lamp failure

detection)

35

40

45

%

IQ

t(s) Vth

roduc Notes :1.

P 2.

te 3.

le 4.

o 5.

Current Consumption Relay off

Ipin 1

Lamp Failure Threshold

(see note 4)

VS = 8V

VS = 13.5V

VS = 18V

R3 = 220Ω

VS = 13.5V

–20 < Tamb < 100°C

2.2

3.9

mA

2.7

4.3

mA

3.3

4.7

mA

65

85

95

mV

This voltage is the threshold used to protect the circuit against overvoltage : if Vbat is > than this threshold, the relay will be on

and the voltage across the circuit will maintain constant increasing the current in the protective resistor R3.

This is the maximum value for operation. This value must be higher than 1 K Ohms in order to limit the current in pin 8 during

dumps. A recommended value for application should be 1,5 K Ohms.

The external leakage from the blinker unit to ground must be with an equivalent resistor higher than 5,6 K Ohms to avoid para-

sitic operation when the switch S1 is off.

This temperature coefficient is usefull to compensate the drift of the external timing network (R1, C1).

This threshold is calculated for a 20 m Ohm shunt. The threshold is dependant of Vbat as the bulb current.

roduct(s) - Obs FUNCTIONAL DESCRIPTION

P The circuit is designed to drive the direction indi-

te cator flasher relay. The application circuit shows

le the typical system configuration with the external

components. Its consists of a network (R1 C1) to

o determine the oscillator frequency, shunt resistor

bs (RS) to detect defective bulbs and two current lim-

iting resistors (R2/R3) to protect the IC against

Oload dump transients.

by closing S1 : then, after a delay time td typically

equal to 1.5 ms, the relay is actuated and the pin

3 goes high switching on the corresponding

lamps L2, L3, (or L4, L5). These lamps will flash at

the oscillator frequency not depending on the bat-

tery voltage value (8 - 18 V). The flashing cycle

stops and the circuit is reset to the initial position

when the switch S1 is open.

The lamp failure detection function senses the

The lightbulbs L2, L3, L4, L5, are the turn signal in-

current through the shunt resistor RS. When one

of the lightbulbs is defective the voltage drop

dicators with the dashboard-light L6. The S1

switch position is sensed across resistor R2

across RS is reduced to a half and the failure is

indicated by doubling the flashing frequency.

and Rlamp by input 8. The flashing cycle is started

3/7

Share Link: