DS1374U-33 查看數據表（PDF） - Maxim Integrated

零件编号

产品描述 (功能)

生产厂家

DS1374U-33

I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output

Maxim Integrated 

I2C, 32-Bit Binary Counter Watchdog RTC with

Trickle Charger and Reset Input/Output

POWER-UP/POWER-DOWN CHARACTERISTICS

(TA = -40°C to +85°C) (Figure 3)

PARAMETER

SYMBOL

CONDITIONS

VCC Detect to Recognize Inputs

(VCC Rising)

VCC Fall Time; VPF(MAX) to

VPF(MIN)

VCC Rise Time; VPF(MIN) to

VPF(MAX)

tRPU (Note 24)

tF

tR

MIN TYP MAX UNITS

250

ms

300

μs

0

μs

WARNING: Under no circumstances are negative undershoots, of any amplitude, allowed when the device is in write protection.

Note 2: Limits at -40°C are guaranteed by design and not production tested.

Note 3: All voltages are referenced to ground.

Note 4: VBACKUP should not exceed VCC MAX or 3.7V, whichever is greater.

Note 5: The use of the 250Ω trickle-charge resistor is not allowed at VCC > 3.63V and should not be enabled.

Note 6: Measured at VCC = typ, VBACKUP = 0V, register 09h = A5h.

Note 7: Measured at VCC = typ, VBACKUP = 0V, register 09h = A6h.

Note 8: Measured at VCC = typ, VBACKUP = 0V, register 09h = A7h.

Note 9: SCL only.

Note 10: SDA and SQW and INT.

Note 11: The RST pin has an internal 50kΩ pullup resistor to VCC.

Note 12: Trickle charger disabled.

Note 13: ICCA—SCL clocking at max frequency = 400kHz.

Note 14: Specified with I2C bus inactive.

Note 15: Measured with a 32.768kHz crystal attached to the X1 and X2 pins.

Note 16: WDSTR = 1. BBSQW = 1 is required for operation when VCC is below the power-fail trip point (or absent).

Note 17: CB—total capacitance of one bus line in pF.

Note 18: After this period, the first clock pulse is generated.

Note 19: The maximum tHD:DAT only has to be met if the device does not stretch the low period (tLOW) of the SCL signal.

Note 20: A device must internally provide a hold time of at least 300ns for the SDA signal (referred to as the VIHMIN of the SCL sig-

nal) to bridge the undefined region of the falling edge of SCL.

Note 21: A fast-mode device can be used in a standard-mode system, but the requirement tSU:DAT ≥ to 250ns must be met. This is

automatically the case if the device does not stretch the low period of the SCL signal. If such a device does stretch the low

period of the SCL signal, it must output the next data bit to the SDA line tR max + tSU:DAT = 1000 + 250 = 1250ns before

the SCL line is released.

Note 22: Guaranteed by design. Not production tested.

Note 23: The parameter tOSF is the period of time the oscillator must be stopped for the OSF flag to be set over the voltage range of

0V ≤ VCC ≤ VCC MAX and 1.3V ≤ VBACKUP ≤ 3.7V.

Note 24: This delay applies only if the oscillator is enabled and running. If the EOSC bit is 1, the startup time of the oscillator is

added to this delay.

_____________________________________________________________________ 5

Share Link: