AD5726YRSZ-REEL(Rev0) 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

AD5726YRSZ-REEL
(Rev.:Rev0)

Quad, 12-Bit, Serial Input, Unipolar/Bipolar, Voltage Output DAC

Analog Devices 

MICROPROCESSOR INTERFACING

Microprocessor interfacing to the AD5726 is via a serial bus

that uses standard protocol compatible with microcontrollers

and DSP processors. The communications channel is a 3-wire

interface (minimum) consisting of a clock signal, a data signal,

and a synchronization signal. The AD5726 requires a 16-bit

data-word with data valid on the falling edge of SCLK.

For all the interfaces, the DAC output update can be done

automatically when all the data is clocked in, or it can be done

under the control of LDAC.

MC68HC11 Interface

Figure 28 shows an example of a serial interface between the

AD5726 and the MC68HC11 microcontroller. The serial

peripheral interface (SPI) on the MC68HC11 is configured for

master mode (MSTR = 1); clock polarity bit (CPOL = 0), and

the clock phase bit (CPHA = 1). The SPI is configured by writing

to the SPI control register (SPCR); see the 68HC11 User Manual.

SCK of the MC68HC11 drives the SCLK of the AD5726, the

MOSI output drives the serial data line (SDIN) of the AD5726.

The CS is driven from one of the port lines, in this case PC7.

When data is being transmitted to the AD5726, the CS line

(PC7) is taken low and data is transmitted MSB first. Data

appearing on the MOSI output is valid on the falling edge of

SCK. Eight falling clock edges occur in the transmit cycle; thus,

to load the required 16-bit word, PC7 is not brought high until

the second 8-bit word has been transferred to the DACs input

shift register.

MC68HC11*

MOSI

AD5726*

SDIN

SCK

SCLK

PC7

CS

*ADDITIONAL PINS OMITTED FOR CLARITY.

Figure 28. MC68HC11 to AD5726 Interface

8xC51 Interface

The AD5726 requires a clock synchronized to the serial data.

For this reason, the 8xC51 must be operated in Mode 0. In this

mode, serial data is transferred through RxD, and a shift clock

is output on TxD.

P3.3 and P3.4 are bit-programmable pins on the serial port and

are used to drive CS and LDAC, respectively. The 8Cx51 provides

the LSB of its SBUF register as the first bit in the data stream. The

user must ensure that the data in the SBUF register is arranged

correctly because the DAC expects MSB first. When data is to

be transmitted to the DAC, P3.3 is taken low. Data on RxD is

clocked out of the microcontroller on the rising edge of TxD

and is valid on the falling edge. As a result, no glue logic is

required between this DAC and the microcontroller interface.

AD5726

The 8xC51 transmits data in 8-bit bytes with only eight falling

clock edges occurring in the transmit cycle. Because the DAC

expects a 16-bit word, CS (P3.3) must be left low after the first

eight bits are transferred. After the second byte has been

transferred, the P3.3 line is taken high. The DAC can be

updated using LDAC via P3.4 of the 8xC51

8xC51*

RxD

TxD

P3.3

P3.4

AD5726*

SDIN

SCLK

CS

LDAC

*ADDITIONAL PINS OMITTED FOR CLARITY.

Figure 29. 8xC51 to AD5726 Interface

PIC16C6x/7x Interface

The PIC16C6x/7x synchronous serial port (SSP) is configured as

an SPI master with the clock polarity bit set to 0. This is done by

writing to the synchronous serial port control register (SSPCON).

See the PIC16/17 Microcontroller User Manual. In this example,

I/O port RA1 is being used to pulse CS and enable the serial

port of the AD5726. This microcontroller transfers only eight

bits of data during each serial transfer operation; therefore, two

consecutive write operations are needed. Figure 30 shows the

connection diagram.

PIC16C6x/7x*

AD5726*

SDO/RC5

SCLK/RC3

RA1

SDIN

SCLK

CS

*ADDITIONAL PINS OMITTED FOR CLARITY.

Figure 30. PIC16C6x/7x to AD5726 Interface

Blackfin® DSP interface

Figure 31 shows how the AD5726 can be interfaced to the

Analog Devices Blackfin DSP. The Blackfin has an integrated

SPI port that can be connected directly to the SPI pins of the

AD5726. It also has programmable I/O pins that can be used to

set the state of a digital input such as the LDAC pin.

ADSP-BF531

AD5726*

SPISELx

SCK

MOSI

PF10

CS

SCLK

SDIN

LDAC

*ADDITIONAL PINS OMITTED FOR CLARITY.

Figure 31. Blackfin DSP to AD5726 Interface

Rev. 0 | Page 17 of 20

Share Link: