S25FL064K0SMFI003 Просмотр технического описания (PDF) - Spansion Inc.
Номер в каталоге
Компоненты Описание
производитель
S25FL064K0SMFI003
Spansion Inc.
S25FL064K0SMFI003 Datasheet PDF : 66 Pages
| |||
Data Sheet
9.2 SOC008 wide — 8-pin Plastic Small Outline Package (208-mils Body Width)
PACKAGE
JEDEC
SYMBOL
A
A1
A2
b
b1
c
c1
D
E
E1
e
L
L1
L2
N
θ
θ1
θ2
SOC 008 (inches)
MIN MAX
0.069 0.085
0.002 0.0098
0.067 0.075
0.014 0.019
0.013 0.018
0.0075 0.0095
0.006 0.008
0.208 BSC
0.315 BSC
0.208 BSC
.050 BSC
0.020 0.030
.049 REF
.010 BSC
8
0˚
8˚
5˚
15˚
0˚
SOC 008 (mm)
MIN
MAX
1.753
2.159
0.051
0.249
1.70
1.91
0.356
0.483
0.330
0.457
0.191
0.241
0.152
0.203
5.283 BSC
8.001 BSC
5.283 BSC
1.27 BSC
0.508
0.762
1.25 REF
0.25 BSC
8
0˚
8˚
5˚
15˚
0˚
64
NOTES:
1. ALL DIMENSIONS ARE IN BOTH INCHES AND MILLMETERS.
2. DIMENSIONING AND TOLERANCING PER ASME Y14.5M - 1994.
3. DIMENSION D DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 mm
PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 mm PER SIDE. D AND E1
DIMENSIONS ARE DETERMINED AT DATUM H.
4. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE
BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE
OUTMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF
MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD
FLASH. BUT INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
5. DATUMS A AND B TO BE DETERMINED AT DATUM H.
6. "N" IS THE MAXIMUM NUMBER OF TERMINAL POSITIONS FOR
THE SPECIFIED PACKAGE LENGTH.
7. THE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10 TO 0.25 mm FROM THE LEAD TIP.
8. DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.10 mm TOTAL
IN EXCESS OF THE "b" DIMENSION AT MAXIMUM MATERIAL
CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE
LOWER RADIUS OF THE LEAD FOOT.
9. THIS CHAMFER FEATURE IS OPTIONAL. IF IT IS NOT PRESENT,
THEN A PIN 1 IDENTIFIER MUST BE LOCATED WITHIN THE INDEX
AREA INDICATED.
10. LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED
FROM THE SEATING PLANE.
3602 \ 16-038.03 \ 9.1.6
S25FL064K
S25FL064K_00_03 July 13, 2011
Share Link: 