HT45FM03B(2009) Просмотр технического описания (PDF) - Holtek Semiconductor

Номер в каталоге

Компоненты Описание

производитель

HT45FM03B
(Rev.:2009)

Brushless DC Motor Flash Type 8-Bit MCU

Holtek Semiconductor 

HT45FM03B

· Internal RC Oscillator

The internal oscillator has three fixed frequencies of

either 4MHz, 8MHz or 12MHz, the choice of which is

indicated by the suffix marking next to the part number

of the device used. This oscillator is fully integrated

within the microcontroller and requires no external

components. Note that if this internal system clock op-

tion is selected, as it requires no external pins for its

operation, I/O pins PD2 and PD3 are free for use as

normal I/O pins/

P D 2 In te rn a l R C

PD3

O s c illa to r

N o te : P D 2 /P D 3 u s e d a s n o rm a l I/O s

Internal RC Oscillator

Watchdog Timer Oscillator

The WDT oscillator is a fully integrated free running RC

oscillator with a typical period of 65ms at 5V requiring no

external components. It is selected via configuration op-

tion. If selected, when the device enters the Power Down

Mode, the system clock will stop running, however the

WDT oscillator continues to run and to keep the watch-

dog active. However, as the WDT will consume a certain

amount of power when in the Power Down Mode, for low

power applications, it may be desirable to disable the

WDT oscillator by configuration option.

Power Down Mode and Wake-up

Power Down Mode

All of the Holtek microcontrollers have the ability to enter

a Power Down Mode, also known as the HALT Mode or

Sleep Mode. When the device enters this mode, the nor-

mal operating current, will be reduced to an extremely

low standby current level. This occurs because when

the device enters the Power Down Mode, the system

oscillator is stopped which reduces the power consump-

tion to extremely low levels, however, as the device

maintains its present internal condition, it can be woken

up at a later stage and continue running, without requir-

ing a full reset. This feature is extremely important in ap-

plication areas where the MCU must have its power

supply constantly maintained to keep the device in a

known condition but where the power supply capacity is

limited such as in battery applications.

Entering the Power Down Mode

There is only one way for the device to enter the Power

Down Mode and that is to execute the ²HALT² instruc-

tion in the application program. When this instruction is

executed, the following will occur:

· The system oscillator will stop running and the appli-

cation program will stop at the ²HALT² instruction.

· The Data Memory contents and registers will maintain

their present condition.

· The WDT will be cleared and resume counting if the

WDT clock source is selected to come from the WDT

oscillator. The WDT will stop if its clock source origi-

nates from the system clock.

· The I/O ports will maintain their present condition.

· In the status register, the Power Down flag, PDF, will

be set and the Watchdog time-out flag, TO, will be

cleared.

Standby Current Considerations

As the main reason for entering the Power Down Mode

is to keep the current consumption of the MCU to as low

a value as possible, perhaps only in the order of several

micro-amps, there are other considerations which must

also be taken into account by the circuit designer if the

power consumption is to be minimized. Special atten-

tion must be made to the I/O pins on the device. All

high-impedance input pins must be connected to either

a fixed high or low level as any floating input pins could

create internal oscillations and result in increased cur-

rent consumption. Care must also be taken with the

loads, which are connected to I/Os, which are setup as

outputs. These should be placed in a condition in which

minimum current is drawn or connected only to external

circuits that do not draw current, such as other CMOS

inputs. Also note that additional standby current will also

be required if the configuration options have enabled the

Watchdog Timer internal oscillator.

Wake-up

After the system enters the Power Down Mode, it can be

woken up from one of various sources listed as follows:

· An external reset

· An external falling edge on Port A

· A system interrupt

· A WDT overflow

If the system is woken up by an external reset, the de-

vice will experience a full system reset, however, if the

device is woken up by a WDT overflow, a Watchdog

Timer reset will be initiated. Although both of these

wake-up methods will initiate a reset operation, the ac-

tual source of the wake-up can be determined by exam-

ining the TO and PDF flags. The PDF flag is cleared by a

system power-up or executing the clear Watchdog

Timer instructions and is set when executing the ²HALT²

instruction. The TO flag is set if a WDT time-out occurs,

and causes a wake-up that only resets the Program

Counter and Stack Pointer, the other flags remain in

their original status.

Rev. 1.00

61

December 16, 2009

Share Link: