LTC7000MPMSE-1-PBF 데이터 시트보기 (PDF) - Analog Devices

부품명

상세내역

제조사

LTC7000MPMSE-1-PBF

Fast 150V Protected High Side NMOS Static Switch Driver

Analog Devices 

LTC7000/LTC7000-1

APPLICATIONS INFORMATION

UVLO to 8.0V. The value of RVCCUV is calculated and

rounded to the nearest standard value as follows:

R VCCUV

=

8.0V

70µA

=

113kΩ

The value of the current sense resistor, RSNS is calculated

next. The LTC7000-1 has a fixed current sense thresh-

old, ΔVTH, of 30mV typical and 22mV minimum. To pro-

vide a minimum 3A load current, the minimum specified

ΔVTH = 22mV should be used for the RSNS calculation

below:

RSNS

=

22mV

3A

=

7.3mΩ

The closest standard value is 7mΩ. The power dissipation

of RSNS is 63mW so choose a power rating of greater than

0.25W to provide adequate margin.

The next item to check is to make sure the insertion loss

specification is satisfied. The insertion loss is given by:

( ) PLOSS = ILOAD2 • RDS(ON)(MAX) + RSNS

= 3A2 • (0.043Ω + 0.007Ω) = 0.45W

Which meets the design specification of less than 0.5W.

The fast output slew rate specification of 1V/µs into a 1µF

load can be met by placing a resistor, RG, in series with

the TGUP pin to the MOSFET gate, as well as connecting

TGDN and a capacitor, CG, to ground on the MOSFET

gate. The values of RG and TG can be calculated from the

following expression:

RG

• CG

≅

0.7 • 12V

1V / µs

=

8.4µs

CG needs to have a voltage rating as high as the BVDSS

of the MOSFET. A good choice for CG is the AVX

06032C471KAT2A which has a value of 470pF and a volt-

age rating of 200V. RG is then calculated to be 17.8kΩ.

The bootstrap capacitor CB can be calculated from the

gate charge as specified in the MOSFET data sheet and

CG as follows:

CB

>

QG

1V

+

10

• CG

=

30nC

1V

+

10

•

470pF

≅ 0.33nF. 100nF will be used.

To meet the short-circuit specification, the TIMER pin

should be connected to VCC to enable immediate turn-off

(approximately 70ns) of the MOSFET in the case of an

overcurrent condition. If an overcurrent condition turns

off the MOSFET, it will not turn back on until the INP pin

has cycled low then back high.

The complete circuit is shown in Figure 15.

VIN

8V TO 135V

1µF

VIN

SNS+

VCC

TIMER

FAULT LTC7000-1

SNS–

TGUP

TGDN

INP

BST

VCCUV

113k

GND

TS

100Ω

17.8k

0.007Ω

IRF7815TRPBF

Turn–On Transient

VIN = 135V

VINP

5V/DIV

VLOAD

50V/DIV

0.1µF

10Ω

CG

470pF

200V

LOAD

8V TO 135V

1µF 3A CONTINUOUS MODE

IDMOSFET

1A/DIV

50µs/DIV

7000 F15b

7000 F15

Figure 15. Design Example

For more information www.analog.com

Rev. E

21

Share Link: