ESMH800VSN332MA25S 데이터 시트보기 (PDF) - Unspecified
부품명
상세내역
제조사
ESMH800VSN332MA25S Datasheet PDF : 3 Pages
| |||
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Standard snap-ins, 85℃
SMHSeries
・Endurance with ripple current : 2,000 hours at 85℃
・Non solvent resistant type
・RoHS Compliant
SMM P241
Downsized
Longer life
SMH
◆SPACIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Characteristics
-40 to +85℃
6.3 to 100Vdc
±20% (M)
(at 20℃, 120Hz)
I=0.02CV or 3mA, whichever is smaller.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 5 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
tanδ(Max.)
0.60 0.50 0.40 0.30 0.25 0.20 0.15 0.15 0.15
(at 20℃, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
Z(-25℃)/Z(+20℃)
444332222
Z(-40℃)/Z(+20℃)
15 15 15 10 8 6 6 5 5
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 85℃.
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 85℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
Leakage current
≦The initial specified value
◆DIMENSIONS [mm]
●Terminal Code : VS (φ22 toφ35) : Standard
Sleeve (PET : Black)
Negative mark
PC board pin-out
10
●Terminal Code : LI (φ35)
Sleeve (PET : Black)
Negative mark
PC board pin-out
2-1.2×6
Vent
*
L±2
4.0±0.5
*φD=35mm : 3.5±0.5mm
The standard design has no plastic disc.
2-φ2
Vent
L±2
4.5±1
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E SMH AAA V S N AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 820µF:821, 3,300µF:332)
Dummy terminal code
Terminal code
Voltage code (ex. 6.3V:6R3, 63V:630, 100V:101)
Series code
Category
Please refer to "Product code guide (snap-in type)"
5±0.5
14.2±1
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
255
CAT. No. E1001O
Share Link: 