STK14C88-N45 데이터 시트보기 (PDF) - Unspecified
부품명
상세내역
제조사
STK14C88-N45 Datasheet PDF : 12 Pages
| |||
STK14C88-M
ABSOLUTE MAXIMUM RATINGSa
Voltage on Input Relative to VSS . . . . . . . . . .–0.6V to (VCC + 0.5V)
Voltage on DQ0-7 or HSB . . . . . . . . . . . . . . . .–0.5V to (VCC + 0.5V)
Temperature under Bias. . . . . . . . . . . . . . . . . . . . . –55°C to 125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W
DC Output Current (1 output at a time, 1s duration) . . . . . . . 15mA
DC CHARACTERISTICS
Note a:
Stresses greater than those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at con-
ditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rat-
ing conditions for extended periods may affect reliability.
(VCC = 5.0V ± 10%)e
SYMBOL
ICC1b
ICC2c
ICC3b
ICC4c
ISB1d
ISB2d
IILK
IOLK
VIH
VIL
VOH
VOL
VBL
TA
PARAMETER
Average VCC Current
Average VCC Current during STORE
Average VCC Current at tAVAV = 200ns
Average VCAP Current during AutoStore™
Cycle
Average VCC Current
(Standby, Cycling TTL Input Levels)
VCC Standby Current
(Standby, Stable CMOS Input Levels)
Input Leakage Current
Off-State Output Leakage Current
Input Logic “1” Voltage
Input Logic “0” Voltage
Output Logic “1” Voltage
Output Logic “0” Voltage
Logic “0” Voltage on HSB Output
Operating Temperature
MILITARY
MIN
MAX
90
85
6
15
4
30
28
3
±1
2.2
VSS – .5
2.4
– 55
±5
VCC + .5
0.8
0.4
0.4
125
UNITS
mA
mA
mA
mA
mA
mA
mA
mA
µA
µA
V
V
V
V
V
°C
NOTES
tAVAV = 35ns
tAVAV = 45ns
All Inputs Don’t Care, VCC = max
W ≥ (VCC – 0.2V)
All Others Cycling, CMOS Levels
All Inputs Don’t Care
tAVAV = 35ns, E ≥ VIH
tAVAV = 45ns, E ≥ VIH
E ≥ (VCC – 0.2V)
All Others VIN ≤ 0.2V or ≥ (VCC – 0.2V)
VCC = max
VIN = VSS to VCC
VCC = max
VIN = VSS to VCC, E or G ≥ VIH
All Inputs
All Inputs
IOUT = – 4mA except HSB
IOUT = 8mA except HSB
IOUT = 3mA
Note b:
Note c:
Note d:
Note e:
ICC1 and ICC3 are dependent on output loading and cycle rate. The specified values are obtained with outputs unloaded.
IECC≥2VaInHdwIiCllCn4oat rperothdeucaevesrtaagnedbcyurcruernrtesnrteleqvueirlesdufnotril
the duration of the respective STORE
any nonvolatile cycle in progress has
cycles
timed
(tSTORE
out.
)
.
VCC reference levels throughout this datasheet refer to VCCX if that is where the power supply connection is made, or VCAP if VCCX is con-
nected to ground.
AC TEST CONDITIONS
Input Pulse Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to 3V
Input Rise and Fall Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .≤ 5ns
Input and Output Timing Reference Levels. . . . . . . . . . . . . . . . 1.5V
Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1
5.0V
480 Ohms
CAPACITANCEf (TA = 25°C, f = 1.0MHz)
SYMBOL
PARAMETER
MAX UNITS CONDITIONS
CIN
COUT
Input Capacitance
5
Output Capacitance
7
pF
∆V = 0 to 3V
pF
∆V = 0 to 3V
Note f: These parameters are guaranteed but not tested.
OUTPUT
255 Ohms
30 pF
INCLUDING
SCOPE
AND FIXTURE
Figure 1: AC Output Loading
April 1999
5-44
Share Link: 