DEC1X3J270JC4B 데이터 시트보기 (PDF) - Unspecified
부품명
상세내역
제조사
DEC1X3J270JC4B Datasheet PDF : 74 Pages
| |||
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C85E.pdf
Sep.14,2018
Type KJ Specifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Appearance No marked defect
Capacitance Within the specified tolerance
10 Vibration
D.F.
Char.
B, E
Specifications
D.F.<=2.5%
11
Mechanical
Shock
Appearance
Capacitance
D.F.
No marked defect
Within the specified tolerance
Char.
B, E
Specifications
D.F.<=5.0%
I.R.
10000MΩ min.
Humidity
12
(Under
Steady
State)
13
Humidity
Loading
Appearance
Capacitance
Change
No marked defect
Char.
B
E
Capacitance Change
Within ±10%
Within ±15%
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Char.
B, E
3000MΩ min.
Specifications
D.F.<=5.0%
Per Item 6
No marked defect
Char.
B
E
Capacitance Change
Within ±10%
Within ±15%
D.F.
I.R.
Appearance
Capacitance
Change
I.R.
Char.
B, E
3000MΩ min.
No marked defect
Within ±20%
3000MΩ min.
Specifications
D.F.<=5.0%
14 Life
Dielectric
Strength
Per Item 6
Test Method
Solder the capacitor and gum
up the body to the test jig
(glass epoxy board) by resin
Resin (Adhesive)
(adhesive).
The capacitor should be firmly soldered to the supporting lead
wire, 1.5mm in total amplitude, with about a 20 minutes rate of
vibration change from 10Hz to 2000Hz and back to 10Hz.
This motion should be applied 12 times in each of 3 mutually
perpendicular directions (total of 36 times).
The acceleration is 5g max.
Solder the capacitor and gum
up the body to the test
jig (glass epoxy board) by resin
Resin (Adhesive)
(adhesive).
Three shocks in each direction should be applied along 3
mutually perpendicular axes to and from of the test specimen
(18 shocks).
The specified test pulse should be half-sine and should have a
duration: 0.5ms, peak value: 100g and velocity change: 4.7m/s
Set the capacitor for 1000±12h at 85±3°C in 80 to 85%
relative humidity.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1h, then placed at
room condition* for 24±2h before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2h at room condition*.
Apply the rated voltage for 1000±12h at 85±3°C in 80 to 85%
relative humidity.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1h, then placed at
room condition* for 24±2h before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2h at room condition*.
Impulse Voltage
Each individual capacitor should be subjected to a 5kV
impulses for three times. Then the capacitors are applied to life
test.
100 (%)
90
50
Front time (T1) =1.2μs=1.67T
Time to half-value (T2) =50μs
30
0
t
T
T1
T2
Apply a voltage from Table 4 for 1000h at 125+2/-0°C, and
relative humidity of 50% max.
<Table 4>
Applied Voltage
AC510V(r.m.s.) <50/60Hz>, except that once each hour
the voltage is increased to AC1000V(r.m.s.) for 0.1s.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1h, then placed at
room condition* for 24±2h before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2h at room condition*.
9
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 106kPa
Continued on the following page.
61
Share Link: 