HC55171BIM 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
HC55171BIM Datasheet PDF : 11 Pages
| |||
HC55171B
Absolute Maximum Ratings TA = 25oC
Maximum Supply Voltages
(VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7V
(VCC)-(VBAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90V
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +15V
Operating Conditions
Temperature Range
HC55171BIM, HC55171BIB . . . . . . . . . . . . . . . . . . -40oC to 85oC
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V to +12V
Positive Power Supply (VCC) . . . . . . . . . . . . . . . . . . . . . . . +5V ±5%
Negative Power Supply (VBAT). . . . . . . . . . . . . . . . . . . -16V to -80V
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
PLCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
Maximum Junction Temperature, Plastic Packages . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(SOIC, PLCC - Lead Tips Only)
Die Characteristics
Transistor Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Diode Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Die Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 x 144
Substrate Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VBAT
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bipolar-DI
ESD (Human Body Model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied
NOTES:
1. θJA is measured with the component mounted on an evaluation board PC board in free air.
2. All grounds (AGND, BGND) must be applied before VCC or VBAT. Failure to do so may result in premature failure of the part. If a user
wishes to run separate grounds off a line card, the AGND must be applied first.
Electrical Specifications
Unless Otherwise Specified, Typical Parameters are at TA = 25oC, Min-Max Parameters are over
Operating Temperature Range, VBAT = -24V, VCC = +5V, AGND = BGND = 0V. All AC Parameters are specified
at 600Ω 2-Wire terminating impedance.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNITS
RINGING TRANSMISSION PARAMETERS
VRING Input Impedance
4-Wire to 2-Wire Gain
AC TRANSMISSION PARAMETERS
(Note 3)
VRING to VT-R (Note 3)
-
5.4
-
kΩ
-
40
-
V/V
RX Input Impedance
300Hz to 3.4kHz (Note 3)
-
108
-
kΩ
OUT1 Positive Output Voltage Swing
OUT1 Negative Output Voltage Swing
4-Wire Input Overload Level
RL = 10kΩ (Note 3)
+2.5
-
RL = 10kΩ (Note 3)
-4.5
-
300Hz to 3.4kHz RL = 1200Ω, 600Ω Reference
-
+3.1
(Note 3)
-
V
-
V
-
VPEAK
2-Wire Return Loss
Matched for 600Ω, f = 300Hz (Note 3)
37
-
-
dB
Matched for 600Ω, f = 1000Hz (Note 3)
40
-
-
dB
Matched for 600Ω, f = 3400Hz (Note 3)
30
-
-
dB
2-Wire Longitudinal to Metallic Balance
Per ANSI/IEEE STD 455-1976 300Hz to 3400Hz 40
-
Off Hook
(Note 3)
-
dB
4-Wire Longitudinal Balance Off Hook
Longitudinal Current Capability
Insertion Loss, 2-Wire to 4-Wire
300Hz to 3400Hz (Note 3)
40
ILINE = 40mA, TA = 25oC (Note 3)
-
0dBmO, 1kHz, Includes Transhybrid Amp Gain = 3
-
-
40
±0.05
-
-
±0.2
dB
mARMS
dB
Insertion Loss, 4-Wire to 2-Wire
0dBmO,1kHz
-
±0.05 ±0.2
dB
Insertion Loss, 4-Wire to 4-Wire
0dBmO, 1kHz, Includes Transhybrid Amp Gain = 3
-
-
±0.35
dB
Frequency Response
300Hz to 3400Hz Referenced to Absolute Level
-
±0.02 ±0.06
dB
at 1kHz, 0dBm Referenced 600Ω
64
Share Link: 