NCV59150 データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
メーカー
NCV59150 Datasheet PDF : 14 Pages
| |||
NCP59150, NCV59150 Series
ELECTRICAL CHARACTERISTICS
TJ = 25C with VIN = VOUT nominal + 1 V; VEN = VIN; IL = 10 mA; bold values indicate –40C < TJ < +125C, unless noted.
Parameter
Conditions
Min
Typ
Max Unit
Output Voltage Accuracy
DFN package
IL = 10 mA
10 mA < IOUT < 1.5 A , VOUT nominal + 1 VIN 13.5 V
Output Voltage Accuracy
D2PAK package
IL = 10 mA
10 mA < IOUT < 1.5 A , VOUT nominal + 1 VIN 13.5 V
Output Voltage Line Regulation
VIN = VOUT nominal + 1.0 V to 13.5 V; IL = 10 mA
Output Voltage Load Regulation
IL = 10 mA to 1.5 A
VIN – VOUT Dropout Voltage (Note 7) IL = 750 mA
IL = 1.5 A
Ground Pin Current (Note 8)
IL = 1.5 A
−1
1
%
−2
2
%
−1.5
1.5
%
−2.5
2.5
%
0.02
0.5
%
0.2
1.0
%
175
350
mV
300
500
mV
40
60
mA
80
Ground Pin Current in Shutdown
Overload Protection Current Limit
Start−up Time
Output Voltage Start−up Slope
Fixed Voltage Devices
VEN v 0.5 V
VOUT = 0 V
VEN = VIN, VOUT nominal = 2.5 V, IOUT = 10 mA,
COUT = 47 mF
VEN = VIN, IOUT = 10 mA, COUT = 47 mF (Note 9)
1.0
5.0
mA
2.0
3.0
A
100
500
ms
40
200
ms/V
ENABLE INPUT
Enable Input Signal Levels
Regulator Enable
1.8
V
Regulator Shutdown
0.8
V
Enable Pin Input Current
VEN v 0.8 V (Regulator Shutdown)
2.0
mA
4.0
6.5 V > VEN w 1.8 V (Regulator enable)
1.0
15
30
mA
40
FLAG OUTPUT
IFLG(leak)
Voh = 13.5 V, Flag OFF
1.0
mA
2.0
VFLG(LO)
VIN = 2.24 V, IFLG = 1 mA, Flag ON
210
400
mV
500
VFLG
Low Threshold, % of particular VOUT
Hysteresis, % of particular VOUT
High Threshold, % of particular VOUT
NCP/NCV59152 ADJ VOLTAGE DEVICES ONLY
93
95
%
2
%
97
99.2
%
Reference Voltage DFN Package
D2PAK Package
1.228 1.240 1.252
V
1.215
1.265
1.221 1.240 1.259
1.209
1.271
Adjust Pin Bias Current
100
200
nA
350
7. VDO = VIN – VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1 V. For output voltages below 1.74 V, dropout
voltage specification does not apply due to a minimum input operating voltage of 2.24 V.
8. IIN = IGND + IOUT.
9. Fixed Voltage Device Start−up Time = Output Voltage Start−up Slope * VOUT nominal.
Package
D2PAK–3, Junction−to−Case
D2PAK–5, Junction−to−Case
D2PAK–3, Junction−to−Air
D2PAK–5, Junction−to−Air
DFN8, Junction−to−Air
Conditions / PCB Footprint
PCB with 100 mm2 2.0 oz Copper Heat Spreading Area
PCB with 100 mm2 2.0 oz Copper Heat Spreading Area
PCB with 500 mm2 2.0 oz Copper Heat Spreading Area
Thermal Resistance
RqJC = 2.1C/W
RqJC = 2.1C/W
RqJA = 52C/W
RqJA = 52C/W
RqJA = 75C/W
http://onsemi.com
4
Share Link: 