S70FL256P0XMHI211 データシートの表示（PDF） - Cypress Semiconductor

部品番号

コンポーネント説明

メーカー

S70FL256P0XMHI211

256-Mbit 3.0V Flash

Cypress Semiconductor 

S70FL256P

11. Physical Dimensions

11.1 SL3 016 — 16-pin Wide Plastic Small Outline Package (300-mil Body Width)

PACKAGE

JEDEC

SYMBOL

A

A1

A2

b

b1

c

c1

D

E

E1

e

L

L1

L2

N

h

θ

θ1

θ2

Design

nded for New SL3016(inches)

e MS-013(D)AA

MIN MAX

m 0.093 0.104

0.004 0.012

m 0.081 0.104

o 0.012 0.020

c 0.011 0.019

e 0.008 0.013

0.008 0.012

R 0.406 BSC

t0.406 BSC

o0.295 BSC

N.050 BSC

SL3016 (mm)

MS-013(D)AA

MIN

MAX

2.35

2.65

0.10

0.30

2.05

2.55

0.31

0.51

0.27

0.48

0.20

0.33

0.20

0.30

10.30 BSC

10.30 BSC

7.50 BSC

1.27 BSC

NOTES:

1. ALL DIMENSIONS ARE IN BOTH INCHES AND MILLMETERS.

2. DIMENSIONING AND TOLERANCING PER ASME Y14.5M - 1994.

3. DIMENSION D DOES NOT INCLUDE MOLD FLASH,

PROTRUSIONS OR GATE BURRS. MOLD FLASH,

PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 mm

. PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD

FLASH OR PROTRUSION INTERLEAD FLASH OR PROTRUSION

SHALL NOT EXCEED 0.25 mm PER SIDE. D AND E1

DIMENSIONS ARE DETERMINED AT DATUM H.

4. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE

BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE

OUTMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF

MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD

FLASH. BUT INCLUDING ANY MISMATCH BETWEEN THE TOP

AND BOTTOM OF THE PLASTIC BODY.

5. DATUMS A AND B TO BE DETERMINED AT DATUM H.

6. "N" IS THE MAXIMUM NUMBER OF TERMINAL POSITIONS FOR

THE SPECIFIED PACKAGE LENGTH.

7. THE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD

0.016 0.050

0.40

1.27

BETWEEN 0.10 TO 0.25 mm FROM THE LEAD TIP.

.055 REF

.010 BSC

16

0.10 0.30

0°

8°

5°

15°

1.40 REF

0.25 BSC

16

0.25

0.75

0°

8°

5°

15°

8. DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION.

ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.10 mm TOTAL

IN EXCESS OF THE "b" DIMENSION AT MAXIMUM MATERIAL

CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE

LOWER RADIUS OF THE LEAD FOOT.

9. THIS CHAMFER FEATURE IS OPTIONAL. IF IT IS NOT PRESENT,

THEN A PIN 1 IDENTIFIER MUST BE LOCATED WITHIN THE INDEX

AREA INDICATED.

0°

0°

10. LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED

FROM THE SEATING PLANE.

3644 \ 16-038.03 Rev C \ 02.03.10 (JK)

Document Number: 002-00647 Rev. *F

Page 12 of 16

Share Link: