ADSP-2104L データシートの表示（PDF） - Analog Devices
部品番号
コンポーネント説明
メーカー
ADSP-2104L Datasheet PDF : 36 Pages
| |||
ADSP-2104L/ADSP-2109L–SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
Parameter
VDD
TAMB
Supply Voltage
Ambient Operating Temperature
See “Environmental Conditions” for information on thermal specifications.
K Grade
Min
Max
3.00
3.60
0
+70
ELECTRICAL CHARACTERISTICS
Parameter
Test Conditions
Min
VIH
Hi-Level Input Voltage1, 3
@ VDD = max
2.0
VIL
Lo-Level Input Voltage1, 3
@ VDD = min
VOH
Hi-Level Output Voltage2, 3, 6
@ VDD = min, IOH = –0.5 mA6
2.4
VOL
Lo-Level Output Voltage2, 3, 6
@ VDD = min, IOL = 2 mA6
IIH
Hi-Level Input Current1
@ VDD = max, VIN = VDD max
IIL
Lo-Level Input Current1
@ VDD = max, VIN = 0 V
IOZH
Three-State Leakage Current4
@ VDD = max, VIN = VDD max5
IOZL
Three-State Leakage Current4
@ VDD = max, VIN = 0 V5
CI
Input Pin Capacitance1, 7, 8
@ VIN = 2.5 V, fIN = 1.0 MHz, TAMB = 25°C
CO
Output Pin Capacitance4, 7, 8, 9
@ VIN = 2.5 V, fIN = 1.0 MHz, TAMB = 25°C
NOTES
1Input-only pins: CLKIN, RESET, IRQ2, BR, MMAP, DR1, DR0.
2 Output pins: BG, PMS, DMS, BMS, RD, WR, A0–A13, CLKOUT, DT1, DT0.
3 Bidirectional pins: D0–D23, SCLK1, RFS1, TFS1, SCLK0, RFS0, TFS0.
4 Three-stateable pins: A0–A13, D0–D23, PMS, DMS, BMS, RD, WR, DT1, SCLK1, RSF1, TFS1, DT0, SCLK0, RFS0, TFS0.
5 0 V on BR, CLKIN Active (to force three-state condition).
6 All outputs are CMOS and will drive to VDD and GND with no dc loads.
7 Guaranteed but not tested.
8 Applies to PLCC package type.
9Output pin capacitance is the capacitive load for any three-stated output pin.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +4.5 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Output Voltage Swing . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range (Ambient) . . . .–40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (5 sec) PLCC . . . . . . . . . . . . . . . . +280°C
*Stresses greater than those listed above may cause permanent damage to the
device. These are stress ratings only, and functional operation of the device at these
or any other conditions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Max
0.4
0.4
10
10
10
10
8
8
Unit
V
°C
Unit
V
V
V
V
µA
µA
µA
µA
pF
pF
–16–
REV. 0
Share Link: 