HIP1013 Ver la hoja de datos (PDF) - Renesas Electronics
Número de pieza
componentes Descripción
fabricante
HIP1013 Datasheet PDF : 7 Pages
| |||
HIP1013
NOT RECOMMENDED FOR NEW DESIGNS
NO RECOMMENDED REPLACEMENT
c1o-8n8t8a-cItNoTuErRTSeIcLhonricwawl Swu.ipnpteorrstiCl.ceonmte/rtsact
Low Cost Dual Power Distribution Controller
DATASHEET
FN4516
Rev 3.00
August 2004
The HIP1013 is a low cost HOT SWAP dual supply power
distribution controller. Two external N-Channel MOSFETs are
driven to distribute power while providing load fault isolation. At
turn-on, the gate of each external N-Channel MOSFET is
charged with a 10A current source. Capacitors on each gate
(see the Typical Application Diagram), create a programmable
ramp (soft turn-on) to control inrush currents. A built in charge
pump supplies the gate drive for the 12V supply N-Channel
MOSFET switch.
Over current protection is facilitated by two external current
sense resistors. When the current through either resistor
exceeds the user programmed value the N-Channel MOSFETs
are latched off by the HIP1013. The controller is reset by a
rising edge on either PWRON pin.
Choosing the voltage selection mode the HIP1013 controls
either +12V/5V or +3.3V/+5V supplies.
Although pin compatible with the HIP1012 device, the HIP1013
does not offer current regulation during an OC event.
Ordering Information
PART
NUMBER
TEMP.
RANGE (°C)
PACKAGE
PKG.
DWG. #
HIP1013CB
-0 to 70
14 Ld SOIC
M14.15
HIP1013CBZA (Note)
-0 to 70
14 Ld SOIC
(Pb-free)
M14.15
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
*Tape & Reel packaging available with “-T” suffix..
Pinout
HIP1013 (SOIC)
TOP VIEW
3/12VS 1
3/12VG 2
VDD 3
MODE/
PWRON1
4
PWRON2 5
5VG 6
5VS 7
14 3/12VISEN
13 RILIM
12 GND
11 CPUMP
10 NC
9 PGOOD
8 5VISEN
Features
• HOT SWAP Dual Power Distribution Control for +5V and
+12V or +5V and +3.3V
• Provides Fault Isolation
• Charge Pump Allows the Use of N-Channel MOSFETs
• Redundant Power On Controls
• Power Good and Over Current Latch Indicators
• Adjustable Turn-On Ramp
• Protection During Turn-On
• Pb-free Available
Applications
• Power Distribution Control
• Hot Plug™ Components
Typical Application Diagram
CPUMP
12V
VDD
CGATE
POWER ON
INPUTS
5V
CGATE
RSENSE
HIP1013
3/12VISEN
3/12VS
3/12VG
VDD
M/PON1
RILIM
GND
CPUMP
PWRON2
NC
5VG
PGOOD
5VS
5ISEN
RSENSE
RLOAD
RILIM
5V
RLOAD
FN4516 Rev 3.00
August 2004
Page 1 of 7
Share Link: 