SST29EE010A Ver la hoja de datos (PDF) - Silicon Storage Technology
Número de pieza
componentes Descripción
fabricante
SST29EE010A Datasheet PDF : 26 Pages
| |||
1 Megabit Page Mode EEPROM
SST29EE010A / SST29LE010A / SST29VE010A
TABLE 3: OPERATION MODES SELECTION
Mode
CE# OE#
Read
VIL
VIL
Page Write
VIL
VIH
Standby
VIH
X
Write Inhibit
X
VIL
Write Inhibit
X
X
Software Chip Erase VIL
VIH
Product Identification
Hardware Mode
VIL
VIL
Software Mode
SDP Enable Mode
VIL
VIH
VIL
VIH
WE#
VIH
VIL
X
X
VIH
VIL
VIH
VIL
VIL
DQ
DOUT
DIN
High Z
High Z/ DOUT
High Z/ DOUT
DIN
Address
AIN
AIN, See Table 4
X
X
X
AIN, See Table 4
Manufacturer Code (BF)
Device Code (see notes)
A16 - A1 = VIL, A9 = VH, A0 = VIL
A16 - A1 = VIL, A9 = VH, A0= VIH
See Table 4
See Table 4
303 PGM T3.0
TABLE 4: SOFTWARE COMMAND CODES
Command
Sequence
Page Write
Software Chip
Erase
Software ID Entry
1st Bus
Write Cycle
Addr(1) Data
5555H AAH
5555H AAH
5555H AAH
2nd Bus
Write Cycle
Addr(1) Data
2AAAH 55H
2AAAH 55H
2AAAH 55H
3rd Bus
Write Cycle
Addr(1) Data
5555H A0H
5555H 80H
4th Bus
Write Cycle
Addr(1) Data
Addr(2) Data
5555H AAH
5555H 90H
5th Bus
6th Bus
Write Cycle Write Cycle
Addr(1) Data Addr(1) Data
2AAAH 55H 5555H 10H
Software ID Exit 5555H AAH 2AAAH 55H 5555H F0H
Alternate Software 5555H AAH 2AAAH 55H
ID Entry(3)
5555H 80H 5555H AAH
2AAAH 55H 5555H 60H
303 PGM T4.0
Notes:
(1) Address format A14-A0 (Hex), Addresses A15 and A16 are a “Don’t Care”.
(2) Page Write consists of loading up to 128 bytes (A6 - A0).
(3) Alternate six-byte software Product-ID Command Code
(4) The software Chip Erase function is not supported by the industrial temperature part.
Please contact SST, if you require this function for an industrial temperature part.
Notes for Software Product ID Command Code:
1. With A14 -A1 =0; SST Manufacturer Code = BFH, is read with A0 = 0,
SST29EE010A Device Code = 22H, is read with A0 = 1.
SST29LE010A/29VE010A Device Code = 23H, is read with A0 = 1.
2. The device does not remain in Software Product ID Mode if powered down.
3. This device supports both the JEDEC standard three-byte command code sequence and SST’s original six-byte command code
sequence. For new designs, SST recommends the three-byte command code sequence be used.
© 1999 Silicon Storage Technology, Inc.
6
303-01 2/99
Share Link: 