CY14B101I Ver la hoja de datos (PDF) - Cypress Semiconductor
Número de pieza
componentes Descripción
fabricante
CY14B101I Datasheet PDF : 42 Pages
| |||
PRELIMINARY
CY14C101I
CY14B101I, CY14E101I
Table 12. Register Map Detail (continued)
Register
Description
Watchdog Timer
0x07
D7
D6
D5
D4
D3
D2
D1
D0
WDS
WDW
WDT
WDS Watchdog Strobe. Setting this bit to ‘1’ reloads and restarts the watchdog timer. Setting the bit to ‘0’ has no effect. The
bit is cleared automatically after the watchdog timer is reset. The WDS bit is write only. Reading it always returns a 0.
WDW
Watchdog Write Enable. Setting this bit to ‘1’ disables any WRITE to the watchdog timeout value (D5–D0). This enables
the user to set the watchdog strobe bit without disturbing the timeout value. Setting this bit to ‘0’ allows bits D5–D0 to
be written to the watchdog register when the next write cycle is complete. This function is explained in more detail in
Watchdog Timer on page 22.
WDT
Watchdog timeout selection. The watchdog timer interval is selected by the 6-bit value in this register. It represents a
multiplier of the 32 Hz count (31.25 ms). The range of timeout value is 31.25 ms (a setting of 1) to 2 seconds (setting
of 3 Fh). Setting the watchdog timer register to ‘0’ disables the timer. These bits can be written only if the WDW bit was
set to 0 on a previous cycle.
Interrupt Status/Control
0x06
D7
D6
D5
D4
D3
D2
D1
D0
WIE
AIE
PFE
SQWE
H/L
P/L
SQ1
SQ0
WIE Watchdog Interrupt Enable. When set to ‘1’ and a watchdog timeout occurs, the watchdog timer drives the INT pin and
the WDF flag. When set to ‘0’, the watchdog timeout affects only the WDF flag.
AIE Alarm Interrupt Enable. When set to ‘1’, the alarm match drives the INT pin and the AF flag. When set to ‘0’, the alarm
match only affects the AF flag.
PFE Power Fail Enable. When set to ‘1’, the alarm match drives the INT pin and the PF flag. When set to ‘0’, the power fail
monitor affects only the PF flag.
SQWE
Square Wave Enable. When set to ‘1’, a square wave is driven on the INT pin with frequency programmed using SQ1
and SQ0 bits. The square wave output takes precedence over interrupt logic. If the SQWE bit is set to ‘1’. when an
enabled interrupt source becomes active, only the corresponding flag is raised and the INT pin continues to drive the
square wave.
H/L High/Low. When set to ‘1’, the INT pin is driven active HIGH. When set to ‘0’, the INT pin is open drain, active LOW.
P/L Pulse/Level. When set to ‘1’, the INT pin is driven active (determined by H/L) by an interrupt source for approximately
200 ms. When set to ‘0’, the INT pin is driven to an active level (as set by H/L) until the flags register is read.
SQ1, SQ0
SQ1, SQ0. These bits are used to decide the frequency of the Square wave on the INT pin output when SQWE bit is
set to ‘1’. The following is the frequency output for each combination of (SQ1, SQ0):
(0, 0) - 1 Hz
(0, 1) - 512 Hz
(1, 0) - 4096 Hz
(1, 1) - 32768 Hz
Alarm - Day
D7
D6
D5
D4
D3
D2
D1
D0
0x05
M
0
10s alarm date
Alarm date
Contains the alarm value for the date of the month and the mask bit to select or deselect the date value.
M
Match. When this bit is set to ‘0’, the date value is used in the alarm match. Setting this bit to ‘1’ causes the match circuit
to ignore the date value.
Alarm - Hours
D7
D6
D5
D4
D3
D2
D1
D0
0x04
M
0
10s alarm hours
Alarm hours
Contains the alarm value for the hours and the mask bit to select or deselect the hours value.
M
Match. When this bit is set to ‘0’, the hours value is used in the alarm match. Setting this bit to ‘1’ causes the match
circuit to ignore the hours value.
Document #: 001-54391 Rev. *C
Page 28 of 42
[+] Feedback
Share Link: 