EVAL-AD7265EDZ(RevB) Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

fabricante

EVAL-AD7265EDZ
(Rev.:RevB)

Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC

Analog Devices 

AD7265

AD7265 to ADSP-BF53x

The ADSP-BF53x family of DSPs interface directly to the

AD7265 without any glue logic required. The availability of

secondary receive registers on the serial ports of the Blackfin®

DSPs means only one serial port is necessary to read from both

DOUT pins simultaneously. Figure 44 shows both DOUTA and

DOUTB of the AD7265 connected to Serial Port 0 of the

ADSP-BF53x. The SPORT0 Receive Configuration 1 register

and SPORT0 Receive Configuration 2 register should be set up

as outlined in Table 9 and Table 10.

AD72651

DOUTA

SCLK

CS

DOUTB

VDRIVE

SERIAL

DEVICE A

(PRIMARY)

SERIAL

DEVICE B

(SECONDARY)

ADSP-BF53x1

SPORT0

DR0PRI

RCLK0

RFS0

DR0SEC

VDD

1ADDITIONAL PINS OMITTED FOR CLARITY.

Figure 44. Interfacing the AD7265 to the ADSP-BF53x

Table 9. The SPORT0 Receive Configuration 1 Register

(SPORT0_RCR1)

Setting

Description

RCKFE = 1

Sample data with falling edge of RSCLK

LRFS = 1

Active low frame signal

RFSR = 1

Frame every word

IRFS = 1

Internal RFS used

RLSBIT = 0

Receive MSB first

RDTYPE = 00

Zero fill

IRCLK = 1

Internal receive clock

RSPEN = 1

Receive enabled

SLEN = 1111

16-bit data-word (or may be set to 1101

for 14-bit data-word)

TFSR = RFSR = 1

Table 10. The SPORT0 Receive Configuration 2 Register

(SPORT0_RCR2)

Setting

Description

RXSE = 1

Secondary side enabled

SLEN = 1111

16-bit data-word (or may be set to 1101

for 14-bit data-word)

To implement the power-down modes, SLEN should be set to

1001 to issue an 8-bit SCLK burst. A Blackfin driver for the

AD7265 is available to download at www.analog.com.

Data Sheet

AD7265 TO TMS320C541

The serial interface on the TMS320C541 uses a continuous

serial clock and frame synchronization signals to synchronize

the data transfer operations with peripheral devices like the

AD7265. The CS input allows easy interfacing between the

TMS320C541 and the AD7265 without any glue logic required.

The serial ports of the TMS320C541 are set up to operate in

burst mode with internal CLKX0 (TX serial clock on Serial

Port 0) and FSX0 (TX frame sync from Serial Port 0). The serial

port control registers (SPC) must have the following setup.

Table 11. Serial Port Control Register Setup

SPC

FO

FSM

MCM

TXM

SPC0

0

1

1

1

SPC1

0

1

0

0

The format bit, FO, may be set to 1 to set the word length to

8 bits to implement the power-down modes on the AD7265.

The connection diagram is shown in Figure 45. For signal

processing applications, it is imperative that the frame

synchronization signal from the TMS320C541 provide

equidistant sampling. The VDRIVE pin of the AD7265 takes the

same supply voltage as that of the TMS320C541. This allows the

ADC to operate at a higher voltage than its serial interface, and

therefore, the TMS320C541, if necessary.

AD72651

SCLK

DOUTA

DOUTB

CS

TMS320C5411

CLKX0

CLKR0

CLKX1

CLKR1

DR0

DR1

FSX0

FSR0

VDRIVE

FSR1

VDD

1ADDITIONAL PINS OMITTED FOR CLARITY.

Figure 45. Interfacing the AD7265 to the TMS320C541

Rev. B | Page 24 of 28

Share Link: