AD5310BRM(1999) Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

fabricante

AD5310BRM
(Rev.:1999)

+2.7 V to +5.5 V, 140 mA, Rail-to-Rail Voltage Output 10-Bit DAC in a SOT-23

Analog Devices 

AD5310

AD5310 to 68HC11/68L11 Interface

Figure 26 shows a serial interface between the AD5310 and the

68HC11/68L11 microcontroller. SCK of the 68HC11/68L11

drives the SCLK of the AD5310, while the MOSI output

drives the serial data line of the DAC. The SYNC signal is de-

rived from a port line (PC7). The setup conditions for correct

operation of this interface are as follows: the 68HC11/68L11

should be configured so that its CPOL bit is a 0 and its CPHA

bit is a 1. When data is being transmitted to the DAC, the

SYNC line is taken low (PC7). When the 68HC11/68L11 is

configured as above, data appearing on the MOSI output is valid

on the falling edge of SCK. Serial data from the 68HC11/68L11

is transmitted in 8-bit bytes with only eight falling clock edges

occurring in the transmit cycle. Data is transmitted MSB first. In

order to load data to the AD5310, PC7 is left low after the first

eight bits are transferred, and a second serial write operation is

performed to the DAC and PC7 is taken high at the end of this

procedure.

68HC11/68L11*

PC7

SCK

MOSI

AD5310*

SCLK

DIN

*ADDITIONAL PINS OMITTED FOR CLARITY

Figure 26. AD5310 to 68HC11/68L11 Interface

AD5310 to 80C51/80L51 Interface

Figure 27 shows a serial interface between the AD5310 and the

80C51/80L51 microcontroller. The setup for the interface is as

follows: TXD of the 80C51/80L51 drives SCLK of the AD5310,

while RXD drives the serial data line of the part. The SYNC

signal is again derived from a bit programmable pin on the port.

In this case port line P3.3 is used. When data is to be transmit-

ted to the AD5310, P3.3 is taken low. The 80C51/80L51 trans-

mits data only in 8-bit bytes; thus only eight falling clock edges

occur in the transmit cycle. To load data to the DAC, P3.3 is

left low after the first eight bits are transmitted, and a second

write cycle is initiated to transmit the second byte of data. P3.3

is taken high following the completion of this cycle. The 80C51/

80L51 outputs the serial data in a format which has the LSB

first. The AD5310 requires its data with the MSB as the first bit

received. The 80C51/80L51 transmit routine should take this

into account.

80C51/80L51*

P3.3

TXD

RXD

AD5310*

SCLK

DIN

AD5310 to Microwire Interface

Figure 28 shows an interface between the AD5310 and any

microwire compatible device. Serial data is shifted out on the

falling edge of the serial clock and is clocked into the AD5310

on the rising edge of the SK.

MICROWIRE*

CS

SK

SO

AD5310*

SCLK

DIN

*ADDITIONAL PINS OMITTED FOR CLARITY

Figure 28.␣ AD5310 to MICROWIRE Interface

APPLICATIONS

Using REF19x as a Power Supply for AD5310

Because the supply current required by the AD5310 is extremely

low, an alternative option is to use a REF19x voltage reference

(REF195 for 5 V or REF193 for 3 V) to supply the required

voltage to the part—see Figure 29. This is especially useful if

your power supply is quite noisy or if the system supply voltages

are at some value other than 5 V or 3 V (e.g., 15 V). The REF19x

will output a steady supply voltage for the AD5310. If the low

dropout REF195 is used, the current which it needs to supply to

the AD5310 is 140 µA. This is with no load on the output of the

DAC. When the DAC output is loaded, the REF195 also needs to

supply the current to the load. The total current required (with

a 5 kΩ load on the DAC output) is:

140 µA + (5 V/5 kΩ) = 1.14 mA

The load regulation of the REF195 is typically 2 ppm/mA

which results in an error of 2.3 ppm (11.5 µV) for the 1.14 mA

current drawn from it. This corresponds to a 0.002 LSB error.

+15V

+5V

REF195

140␮A

THREE-WIRE

SERIAL

INTERFACE

SYNC

SCLK

DIN

AD5310

VOUT = 0V TO 5V

Figure 29. REF195 as Power Supply to AD5310

*ADDITIONAL PINS OMITTED FOR CLARITY

Figure 27. AD5310 to 80C51/80L51 Interface

–10–

REV. A

Share Link: