AD9483KSZ-100 Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

fabricante

AD9483KSZ-100

Triple 8-Bit, 140 MSPS A/D Converter

Analog Devices 

AD9483

EVALUATION BOARD

The AD9483 evaluation board offers an easy way to test the

AD9483. It provides ac or dc biasing for the analog input, it

generates the output latch clocks for Single Mode, Dual

Parallel Mode and Dual Interleaved Mode. Each of the three

channels has a reconstruction DAC (A Port only). The board

has several different modes of operation, and is shipped in

the following configuration:

• Single-ended ac coupled analog input (1 V p-p centered

at ground)

• Differential clock inputs (PECL) (See ENCODE section

for TTL drive)

• Internal voltage references connected to externally buff-

ered on-chip reference (VREF OUT)

• Preset for Dual Mode Interleaved

Analog Input

The evaluation board accepts a 1 V p-p input signal centered

at ground for ac coupled input mode (Set Jumpers W4, W5,

W12, W13, W18, W17 to jump Pin 1 to Pin 2). This signal

biased up to 2.5 V by the on-chip reference. Note: input

signal should be bandlimited (filtered) prior to sampling to

avoid aliasing. The analog inputs are terminated to ground

by a 75 Ω resistor on the board. The analog inputs are ac

coupled through 0.1 µF caps C2, C4, C6 on top of the

board. These can be increased to accommodate lower fre-

quency inputs if desired using test points PR1–PR6 on bot-

tom of board. In dc-coupled input mode (Set Jumpers W4,

W5, W12, W13, W18, W17 to jump Pin 3 to Pin 2 ) the

board accepts typical video level signal levels (0 mV to 700 mV)

the signal is level shifted and amplified to 1 V p-p by the

AD8055 preamp. Variable Resistors R98–R100 are used to

adjust dc black level to 2 V at ADC inputs.

Encode

The AD9483 ENCODE input can be driven two ways.

1. Differential PECL (VLO = 3, VHI = 4 nominal). It is

shipped in this mode.

2. Single ended TTL or CMOS. (At Encode Bar–Remove

50 Ω termination resistor R10, add 0.1 µF capacitor C7)

Voltage Reference

The AD9483 has an internal 2.5 V voltage reference (VREF

OUT). This is buffered externally on board to support addi-

tional level shifting circuitry (the AD9483 VREF OUT pin can

drive the three VREF IN pins in applications where level shifting

is not required with no additional buffering). An external refer-

ence may be employed instead to drive each VREF IN pin

independently (requires moving Jumpers W14, W15, and W16).

Single Channel Mode

Single Channel mode sets the AD9483 to produce data on

every clock cycle on output port A only. The maximum speed

in Single Channel mode is 100 MSPS.

Dual Channel Modes (Outputs Clocked at 1/2 Encode Clock)

Dual Channel Interleaved

Sets the ADC to produce data alternately on Port A and Port B.

The maximum speed in this mode is 140 MSPS.

Dual Channel Parallel

Sets the ADC to produce data concurrently on Port A and

Port B. Maximum speed in this mode is 140 MSPS.

DAC Out

The DAC output is a representation of the data on output Port

A only. The DAC is terminated on the board into 75 Ω. Full-

scale voltage swing at DAC output is nominally 0 mV to 800 mV

when terminated into external 75 Ω (doubly terminated).

Output Port B is not reconstructed. The DAC outputs are NOT

filtered and will exhibit sampling noise. The DACs can be pow-

ered down at W1, W2, and W3 (jumper not installed).

Data Ready

An output clock for latching the ADC outputs is available at

Pin 1 at the 25-pin connector. Its complement is located at

Pin 14. The clocks are terminated on the board by a 75 Ω

Thevenin termination to VD/2. The timing on these clock out-

puts can be inverted at W9, W10 (jumper not installed).

Schematics

The schematics for the evaluation board follow. (Note bypass

capacitors for ADC are shown in Figure 15.)

Table III. Evaluation Board Jumper Settings

Mode

W7 (OMS)

Dual Channel/PARALLEL

Dual Channel/INTERLEAVED

SINGLE

LOW

LOW

HIGH

DESIGN NOTES

Maximum frequency for PARALLEL is 140 MHz.

Maximum frequency for INTERLEAVED is 140 MHz.

Maximum frequency for SINGLE is 100 MHz.

DS is tied to ground through a 50 Ω resistor.

DS is left floating.

W6 (I/P)

LOW

HIGH

DON’T CARE

W11 (A_LAT)

DATA_CLK_OUT (4–5)

DATA_CLK_OUT (5–6)

DATA_CLK_OUT (5–6)

W11 (B_LAT)

DATA_CLK_OUT (2–3)

DATA_CLK_OUT (2–3)

NC

–16–

REV. C

Share Link: