DEVICE OVERVIEW
The PIC16F707/PIC16LF707 devices are covered by this data sheet. They are available in 40/44-pin packages. Figure 1-1 shows a block diagram of the PIC16F707/PIC16LF707 devices. Table 1-1 shows the pinout descriptions.

High-Performance RISC CPU:
• Only 35 Single-Word Instructions to Learn:
   - All single-cycle instructions except branches
• Operating Speed:
   - DC – 20 MHz clock input
   - DC – 200 ns instruction cycle
• 8K x 14 Words of Flash Program Memory
• 363 Bytes of Data Memory (SRAM)
• Interrupt Capability
• 8-Level Deep Hardware Stack
• Direct, Indirect and Relative Addressing modes
• Processor Read Access to Program Memory
• Pinout Compatible to other 40-pin PIC16CXXX and PIC16FXXX Microcontrollers

Special Microcontroller Features:
• Precision Internal Oscillator:
   - 16 MHz or 500 kHz operation
   - Factory calibrated to ±1%, typical
   - Software selectable ÷1, ÷2, ÷4 or ÷8 divider
• 31 kHz Low-Power Internal Oscillator
• External Oscillator Block with:
   - 3 crystal/resonator modes up to 20 MHz
   - 3 external clock modes up to 20 MHz
• Power-on Reset (POR)
• Power-up Timer (PWRT)
• Oscillator Start-Up Timer (OST)
• Brown-out Reset (BOR):
   - Selectable between two trip points
   - Disabled in Sleep option
• Watchdog Timer (WDT)
• Programmable Code Protection
• In-Circuit Serial Programming™ (ICSP™) via two pins
• In-Circuit Debug (ICD) via Two Pins
• Multiplexed Master Clear with Pull-up/Input Pin
• Industrial and Extended Temperature Range
• High-Endurance Flash Cell:
   - 1,000 Write Flash Endurance (typical)
   - Flash Retention: >40 years
   - Power-Saving Sleep mode
• Operating Voltage Range:
   - 1.8V to 3.6V (PIC16LF707)
• 1.8V to 5.5V (PIC16F707)

Extreme Low-Power Management PIC16LF707 with nanoWatt XLP:
• Sleep mode: 20 nA @ 1.8V, typical
• Watchdog Timer: 500 nA @ 1.8V, typical
• Timer1 Oscillator: 600 nA @ 1.8V, typical @ 32 kHz

mTouch™ Technology Features:
• Up to 32 Channels
• Two Capacitive Sensing modules:
   - Acquire 2 samples simultaneously
• Multiple Power modes:
   - Operation during Sleep
   - Proximity sensing with ultra low µA current
• Adjustable Waveform Min. and Max. for Optimal Noise Performance
• 1.8V to 5.5V Operation (3.6V max. for PIC16LF707)

Analog Features:
• A/D Converter:
   - 8-bit resolution and up to 14 channels
   - Conversion available during Sleep
   - Selectable 1.024V/2.048V/4.096V voltage reference
• On-chip 3.2V Regulator (PIC16F707 device only)

Peripheral Highlights:
• Up to 35 I/O Pins and 1 Input-only Pin:
   - High current source/sink for direct LED drive
   - Interrupt-on-pin change
   - Individually programmable weak pull-ups
• Timer0/A/B: 8-Bit Timer/Counter with 8-Bit Prescaler
• Enhanced Timer1/3:
   - Dedicated low-power 32 kHz oscillator driver
   - 16-bit timer/counter with prescaler
   - External Gate Input mode with toggle and single shot modes
   - Interrupt-on-gate completion
• Timer2: 8-Bit Timer/Counter with 8-Bit Period Register, Prescaler and Postscaler
• Two Capture, Compare, PWM modules (CCP):
   - 16-bit Capture, max. resolution 12.5 ns
   - 16-bit Compare, max. resolution 200 ns
   - 10-bit PWM, max. frequency 20 kHz
• Addressable Universal Synchronous
   Asynchronous Receiver Transmitter (AUSART)