MAX9038 View Datasheet(PDF) - Maxim Integrated
Part Name
Description
MFG CO.
MAX9038 Datasheet PDF : 15 Pages
| |||
MAX9038–MAX9043/
MAX9050–MAX9053
Micropower, Single-Supply, UCSP/SOT23
Comparator + Precision Reference ICs
Absolute Maximum Ratings
Supply Voltage (VCC to VEE)...................................-0.3V to +6V
OUT (MAX9038).......................................................-0.3V to +6V
All Other Pins................................. (VEE - 0.3V) to (VCC + 0.3V)
Current into Input Pins......................................................±20mA
Output Short-Circuit Duration
(OUT_, REF)..............Indefinite Short Circuit to Either Supply
Continuous Power Dissipation (TA = +70°C)
5-Pin SOT23 (derate 7.10mW/°C above +70°C).........571mW
6-Bump UCSP (derate 3.9mW/°C above +70°C).........308mW
6-Pin SOT23 (derate 8.70mW/°C above +70°C).........696mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin μMAX® (derate 4.1mW/°C above +70°C)...........330mW
10-Pin μMAX (derate 5.6mW/°C above +70°C)...........444mW
Operating Temperature Range............................ -40°C to +85°C
Junction Temperature.......................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (soldering, 10s).................................. +300°C
Bump Reflow Temperature (Note 1)................................. +235°C
Note 1: This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device can
be exposed to during board-level solder attach and rework. This limit permits only the use of the solder profiles recommended
in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and Convection Packaging Reflow.
Preheating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics—A Grade (0.4% Initial Accuracy)
(VCC = +5V, VEE = 0V, VCM = 0V, IOUT = 0A, IREF = 0A, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 2)
PARAMETER
Supply Voltage Range (Note 3)
Supply Current
COMPARATORS
Input Offset Voltage (Note 4)
Input Hysteresis
Input Bias Current
(Notes 5, 6, 7)
SYMBOL
VCC
ICC
CONDITIONS
MAX9040–MAX9043
MAX9050–MAX9053
MAX9040/MAX9041/
MAX9050/MAX9051
MAX9042/MAX9043/
MAX9052/MAX9053
VCC = 2.7V
VCC = 5V
VCC = 2.7V
VCC = 5V
VOS
VHYST
IB
Over entire
common-mode
range
TA = +25°C
TA = -40°C to +85°C
Specified common-mode range
MIN TYP MAX UNITS
2.5
5.5
V
2.7
5.5
47
67
52
72
55
80
µA
60
85
±0.5 ±5.0
mV
±7.0
±3.0
mV
±0.001 ±10.0 nA
Input Offset Current (Note 5)
Common-Mode Voltage Range
(Notes 5, 8)
Common-Mode Rejection Ratio
(Note 5)
IOS
CMVR
CMRR
Specified common-mode range
TA = +25°C
TA = -40°C to +85°C
Specified common-mode range
±0.5
pA
VEE -
0.25
VCC +
0.25
V
VEE
VCC
52
80
dB
Power-Supply Rejection Ratio
Input Capacitance (Note 5)
Output Short-Circuit Current
Output Voltage Low
PSRR
CIN
ISC
VOL
MAX9040–MAX9043, 2.5V ≤ VCC ≤ 5.5V
MAX9050-MAX9053, 2.5V ≤ VCC ≤ 5.5V
VOUT = VEE or VCC
VCC = 5V
VCC = 2.7V
VCC = 5V, ISINK = 8mA
VCC = 2.7V, ISINK = 3.5mA
55
80
dB
55
80
2.5
pF
95
35
mA
0.2 0.55
V
0.15 0.4
μMAX is a registered trademark of Maxim Integrated Products, Inc.
www.maximintegrated.com
Maxim Integrated │ 2
Share Link: 