LT1015MJ8 View Datasheet(PDF) - Linear Technology
Part Name
Description
MFG CO.
LT1015MJ8 Datasheet PDF : 4 Pages
| |||
LT1015
ABSOLUTE MAXIMUM RATINGS
Supply Voltage .......................................................... 7V
Differential Input Voltage ........................................... 5V
Input Voltage
Positive................................................ Supply + 0.5V
Negative .............................................................. – 1V
Input Current (Forced) Positive ............................ 20mA
Latch Pin Voltage........................................ Supply + 1V
Output Current (Continuous) .............................. ±20mA
Operating Temperature Range
LT1015C .................................................. 0°C to 70°C
LT1015M ........................................ – 55°C to 125°C*
Storage Temperature ............................ – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
*Air flow must be provided for TA > 100°C
PACKAGE/ORDER INFORMATION
INPUT A 1
REFERENCE 2
INPUT B 3
LATCH 4
TOP VIEW
8 V+
7 OUTPUT A
6 GND
5 OUTPUT B
J8 PACKAGE
8-LEAD CERDIP
N8 PACKAGE
8-LEAD PDIP
TJMAX = 150°C, θJA = 100°C/ W (J8)
TJMAX = 100°C, θJA = 130°C/ W (N8)
ORDER PART
NUMBER
LT1015CJ8
LT1015CN8
LT1015MJ8
Consult factory for Industrial grade parts.
ELECTRICAL CHARACTERISTICS
V+ = 4.6V to 5.4V, VLATCH = 0V, common mode input voltage = 2.5V, TJ = 25°C, unless otherwise noted.
PARAMETER
CONDITIONS
Input Offset Voltage (Note 1)
VCM = 1.25V to (V + – 1.5V)
Input Bias Current
∆VIN = 0V (Note 2)
Reference Input Current
∆VIN = 0V (Note 2)
Voltage Gain (Note 3)
VOUT = 0.5V to 2.5V, Load = 1 TTL Gate
Common Mode Input Range (Note 5) Minimum Input
Maximum Input
Output High Voltage
Output Low Voltage
Supply Current
IOUT = 4mA
ISINK = 4mA
V + = 5V
Latch Pin High Input Voltage
Device Latched
Latch Pin Low Input Voltage
Device Active
Latch Pin Current
Propagation Delay
Latch Setup Time
∆VIN ≥ 20mV (Note 4)
0°C ≤ TJ ≤ 100°C
– 55°C ≤ TJ ≤ 150°C
MIN
q
q
q
q
1000
q
q
V + – 1.5
q
2.5
q
q
q
q
0.8
q
q
7
q
7
TYP
1
15
30
2500
1.0
V + – 1.0
0.3
55
10
10
2
MAX
UNITS
20
mV
30
µA
60
µA
V/V
1.25
V
V
V
0.5
V
70
mA
2
V
V
1
mA
14
ns
16
ns
ns
The q denotes specifications which apply over the full operating
temperature range.
Note 1: Input offset voltage is the maximum required to drive the output to
a low state of 0.5V and high state of 2.5V.
Note 2: Input currents are measured by applying a large positive
differential input voltage. The resulting input current is divided by two to
obtain input current at ∆VIN = 0V.
Note 3: Voltage gain is guaranteed by design, but not tested.
Note 4: Propagation delay is sample tested in production with a large
overdrive. The limit is guard banded to account for the slight increase
(≈ 500ps) at 20mV overdrive.
Note 5: Common mode input range is the voltage range over which the
differential input offset voltage is less than 20mV. If both inputs remain
inside this common mode range, propagation delay will be unaffected. It
will also be normal if the signal input is below the 1.25V lower limit when
the input transition begins. An increase in propagation delay of up to 10ns
may occur if the signal input is above the upper common mode limit when
the transition begins. Sine wave inputs may not be affected when the peak
exceeds the common mode range if the signal is inside the common mode
range for 10ns before threshold is reached.
2
Share Link: 