CM50TU-24F(1999) View Datasheet(PDF) - MITSUBISHI ELECTRIC
Part Name
Description
View to exact match
CM50TU-24F Datasheet PDF : 4 Pages
| |||
MAXIMUM RATINGS (Tj = 25°C)
Symbol
VCES
VGES
IC
ICM
IE (Note 1)
IEM (Note 1)
PC (Note 3)
Tj
Tstg
Viso
—
—
Parameter
Collector-emitter voltage
Gate-emitter voltage
Collector current
Emitter current
Maximum collector dissipation
Junction temperature
Storage temperature
Isolation voltage
Torque strength
Weight
G-E Short
C-E Short
TC = 25°C
Pulse
TC = 25°C
Pulse
TC = 25°C
Conditions
Main terminal to base plate, AC 1 min.
Main Terminal M4
Mounting holes M5
Typical value
MITSUBISHI IGBT MODULES
CM50TU-24F
HIGH POWER SWITCHING USE
(Note 2)
(Note 2)
Ratings
1200
±20
50
100
50
100
320
–40 ~ +150
–40 ~ +125
2500
1.3 ~ 1.7
2.5 ~ 3.5
570
Unit
V
V
A
A
W
°C
°C
V
N•m
N•m
g
ELECTRICAL CHARACTERISTICS (Tj = 25°C)
Symbol
Parameter
Test conditions
Min.
ICES
Collector cutoff current
VCE = VCES, VGE = 0V
—
VGE(th) Gate-emitter threshold voltage IC = 5.0mA, VCE = 10V
5
IGES
Gate leakage current
VGE = VCES, VCE = 0V
—
Tj = 25°C
—
VCE(sat) Collector-emitter saturation voltage Tj = 125°C
IC = 50A, VGE = 15V
—
Cies
Input capacitance
—
Coes
Output capacitance
VCE = 10V
—
Cres
Reverse transfer capacitance VGE = 0V
—
QG
Total gate charge
VCC = 600V, IC = 50A, VGE = 15V
—
td(on)
Turn-on delay time
—
tr
Turn-on rise time
VCC = 600V, IC = 50A
—
td(off)
Turn-off delay time
VGE1 = VGE2 = 15V
—
tf
Turn-off fall time
RG = 6.3Ω, Inductive load switching operation
—
trr (Note 1) Reverse recovery time
IE = 50A
—
Qrr (Note 1) Reverse recovery charge
—
VEC(Note 1) Emitter-collector voltage
IE = 50A, VGE = 0V
—
Rth(j-c)Q Thermal resistance*1
IGBT part (1/6 module)
—
Rth(j-c)R
FWDi part (1/6 module)
—
Rth(c-f)
Contact thermal resistance
Case to fin, Thermal compoundapplied*2 (1/6 module)
—
Rth(j-c’)Q Thermal resistance
Tc measured point is just under the chips
—
RG
External gate resistance
6.3
Note 1. IE, VEC, trr, Qrr, die/dt represent characteristics of the anti-parallel, emitter to collector free-wheel diode. (FWDi).
2. Pulse width and repetition rate should be such that the device junction temp. (Tj) does not exceed Tjmax rating.
3. Junction temperature (Tj) should not increase beyond 150°C.
4. Pulse width and repetition rate should be such as to cause negligible temperature rise.
*1 : Tc measured point is indicated in OUTLINE DRAWING.
*2 : Typical value is measured by using Shin-etsu Silicone “G-746”.
*3 : If you use this value, Rth(f-a) should be measured just under the chips.
Limits
Typ.
—
6
—
1.8
1.9
—
—
—
550
—
—
—
—
—
2.1
—
—
—
0.11
—
—
Max. Unit
1
mA
7
20
2.4
—
20
0.85
0.5
—
100
50
300
300
150
—
3.2
0.39
0.70
—
0.31V3
63
V
µA
V
nF
nC
ns
ns
µC
V
°C/W
Ω
Aug. 1999
Share Link: 