HSP50215EVAL View Datasheet(PDF) - Intersil
Part Name
Description
View to exact match
HSP50215EVAL Datasheet PDF : 45 Pages
| |||
HSP50215EVAL
2. ___ If a FIR filter design software tool is desired, then
downloading SERINADE from the Intersil Corpora-
tion website into the target directory is recommend-
ed. The web site is found at www.intersil.com and
SERINADE is found under the Products column of
the home page. Select Digital Signal Processing
Products Listing menu item. Select the Develop-
ment Tools menu item. Select the SERINADE menu
item. Download of SERINADE can be done from this
location.
The software must be run from the new target directory
established on the C drive.
Verifying the Control Software and Board Installation
1. ___ On the PC, change the directory to the target direc-
tory where the control software has been installed.
2. ___ Start the program by typing: HSP50215 <Enter>.
3. ___ The MAIN MENU screen will appear. It will look like
Figure 3.
+------------------------------------+
| HSP50215 EVALUATION BOARD SOFTWARE |
+------------------------------------+
MAIN MENU
(0) Board Configuration
(1) Modulator Channel 1 Configuration
(2) Modulator Channel 2 Configuration
(3) Modulator Channel 3 Configuration
(4) Modulator Channel 4 Configuration
(5) Load Configuration File
(6) Save Configuration File
(7) Compute Registers
(8) Configure Board
(9) Test Menu
(10) Exit
ENTER SELECTION: =
(C) Intersil Corporation 1997 Version 1.0
FIGURE 3. MAIN MENU
4. ___ Select item (0) for board configuration and type <En-
ter>. The BOARD INTERFACE MENU will appear as
shown in Figure 4. Use the menu items to change the
default board configuration to match the evaluation
board interface, printer, FPGA addressing and oscil-
lator frequency that you desire. Verify that these set-
tings match the jumper configuration of your
evaluation board.
5. ___ When you have completed making your modifications,
select item (0) and type <Enter> to return to the MAIN
MENU.
6. ___ Select Main Menu item (9) and type <Enter> to enter
the Test Menu. The Test Menu is shown in Figure 5.
7. ___ Select Test Menu Item (6) and type <Enter> to enter
the Test Board submenu.
8. ___ A screen appears that indicates the RAM Address/Da-
ta Bus test results and the HSP50215 data bus test
results. If all the items have passed the test, the board
and software have been properly installed and you
are ready to begin evaluation testing. Skip to step 12.
If any test failed, proceed to step 9.
9. ___ If one of the tests shown on the screen for step 8 did
not pass, then the board jumper configuration should
be reviewed, as it is the most likely culprit.
+-------------------------------------+
| HSP50215 EVALUATION BOARD SOFTWARE |
+------------------------------------+
BOARD INTERFACE MENU
File Name ................ EXAMPLES\EX01QPSK
(1) Interface ...................... ISA
(2) ISA Base Address ............... 0x300
(3) Channel 1 FPGA Address ......... 0
(4) Channel 2 FPGA Address ......... 1
(5) Channel 3 FPGA Address ......... 2
(6) Channel 4 FPGA Address ......... 3
(7) Oscillator Freq ........... 50000000 Hz
(0) Main Menu
ENTER SELECTION:
(C) Intersil Corporation 1997 Version 1.0
FIGURE 4. BOARD INTERFACE SUBMENU
+------------------------------------+
| HSP50215 EVALUATION BOARD SOFTWARE |
+------------------------------------+
TEST MENU
File Name................... EXAMPLES\EX01QPSK
(1) Reset Board
(2) Write to Location While Reset
(3) Read from Location While Reset
(4) Write to Location While Running
(5) Read from Location While Running
(6) Test Board
(0) Main Menu
ENTER SELECTION:
(C) Intersil Corporation 1997 Version 1.0
FIGURE 5. TEST SUBMENU
10. ___ Next, the physical installation should be checked.
11. ___ If the board is properly installed, then a verify that no
ISAbus card addressing contention exists. Steps 9,
10, AND 11 are the leading causes of board test fail-
ure.
5
Share Link: 